All Products

SKU: AF-2167

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that same light. When something passes between the two, and its not transparent to ...

SKU: AF-5940 · MPN: ADA5940

This breakout uses Vishay's TSSP77038 infrared demodulator to give you the raw demodulated output from a 38kHz IR signal, without the extra filtering used in typical remote-control receivers. That makes it a handy choice for reflective sensing, light barriers, fast proximity detection, and modula...

SKU: DF-SEN0503

An infrared break-beam sensor pair for simple, reliable motion detection. The emitter sends a beam of invisible IR light to the receiver — when an object passes between them and breaks the beam, the receiver outputs a signal. Works up to 50 cm at 5 V with a fast response time under 2 ms. The com...

SKU: SF-ROB-09453

This version of the QRE1113 breakout board features an easy-to-use analog output, which will vary depending on the amount of IR light reflected back to the sensor. This tiny board is perfect for line sensing applications and can be used in both 3.3V and 5V systems. The board’s QRE1113 IR refle...

SKU: DF-SEN0523

This IR break-beam photoelectric switch detects objects by sending an invisible infrared beam from an emitter to a receiver. When a non-transparent object passes between the two and breaks the beam, the receiver outputs a signal. It works over distances up to 4 metres with a fast 0.5ms response t...

SKU: SF-SEN-09299

The GP1A57HRJ00F is a slotted optical sensor (photo interrupter) with an infrared emitter on one upright and a shielded infrared detector on the other. When an object passes through the 10 mm gap between the uprights, it breaks the IR beam and the detector registers the interruption. Key Feature...

SKU: AF-2168

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that same light. When something passes between the two, and its not transparent to IR,...

SKU: DF-SEN0280

The MB1360 XL-MaxSonar-AEL0 sensor features centimeter resolution and a 10Hz read rate, and provides short to long distance detection and range information from 25cm to 1068. This sensor has the widest and most sensitive beam pattern of any unit from the XL-MaxSonar-AE sensor line and includes va...

SKU: DF-SEN0347

This infrared photoelectric switch consists of a transmitter and receiver pair that detects objects at distances up to 1.5 m with a response time under 1 ms. The infrared beam provides stable detection regardless of ambient lighting, making it suitable for both indoor and outdoor use across a −20...

SKU: AF-5913 · MPN: ADA5913

The Adafruit STEMMA Reflective Photo Interrupt Sensor uses a TCRT1000 right-angle optical module to detect reflective surfaces. An onboard IR LED emits light, and when an object reflects it back to the IR phototransistor, the output pin drops from high toward 0V — making it easy to detect the pre...

SKU: AF-3317

The Adafruit VL53L0X is a Time-of-Flight (ToF) distance sensor from ST that uses an invisible laser to measure distances from approximately 50 mm to 1200 mm. By timing how long the laser light takes to bounce back, it delivers precise distance readings without the linearity issues or double-imagi...

SKU: EF-EF04032

The Octopus Analog Photocell Brick is a light-dependent resistor (LDR) module from the ElecFreaks Octopus Electronic Bricks series. It uses a cadmium-sulfide (CdS) photocell that changes resistance based on ambient light levels — the brighter the light, the lower the resistance. With its 3-pin co...

SKU: AF-5990 · MPN: ADA5990

The Adafruit Infrared IR Remote Transceiver combines a high-powered IR transmitter and a sensitive 38 kHz IR receiver on a single board. With two 940 nm IR LEDs (one vertical, one horizontal) driven by an onboard N-channel FET at 100–200 mA per LED, you get 10+ metres of transmit range alongside ...

SKU: SF-COM-00532

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard, yellow LED. The lens is 3mm in diameter and it is diffused.

SKU: DF-TEL0111

INTRODUCTION   The ESP32 WiFi and Bluetooth chip is the latest generation of Espressif products. It has a dual-core 32-bit MCU, which integrates WiFi HT40 and Bluetooth/BLE 4.2 technology inside. Compared to the arduino ESP8266 (the previous generation), the ESP32 has a significant ...

SKU: DF-FIT0244

A pack of 50 basic 3mm LEDs in five colours — 10 each of red, green, yellow, white, and blue. Handy for prototyping, indicator lights, and Arduino projects. Specifications Forward Voltage – 1.8–2.2V Max Current – 20 mA Recommended Current – 16–18 mA LED Size – 3 mm diameter, 23 mm total len...

SKU: PI-COM0613

A clear 5mm infrared LED operating at 940nm wavelength. Ideal for generic IR systems including remote controls, proximity sensors, and touchless object detection. Specifications Wavelength: 940nm (infrared) Forward Voltage: 1.5V DC Max Forward Current: 50mA Package: 5mm clear through-hole ...

SKU: SF-COM-00533

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: AF-4202

Need some miniature indicators? We are big fans of these diffused LEDs. They are fairly bright, so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Now you can get a pack of 25 with 5 different colors Pack of 25 diffuse...

SKU: DF-DFR1136 · MPN: DFR1136

This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....