All Products

SKU: AF-3848

An isolated Power over Ethernet (PoE) module that extracts power from the Ethernet cable's centre taps and outputs a regulated 5 V at up to 1.8 A. The built-in isolation transformer ensures there is no direct electrical connection between the Ethernet side and the 5 V output — important for safet...

SKU: AF-4256

Wanna improve the connection strength between your project's 3D-printed parts, and also have nice clean surfaces? Instead of gluing bits together, or screwing plastic screws directly into your 3D prints, use strong and reusable machine screws and heat-set inserts. Heat set inserts are only a few ...

SKU: AF-5931 · MPN: ADA5931

This PCIe Flex Cable gives you a variety of options for connecting and placing your Pimoroni NVMe Base with Raspberry Pi 5. They have a 'one way' design with 16 pads at the Raspberry Pi 5 end and 18 pins at the NVMe Base end to prevent incorrect installation. The designed is set up for PCIe Gen 3...

SKU: SF-PRT-10687

A 33-metre roll of polyimide (Kapton-style) tape that withstands temperatures up to 258°C (496°F). This high-temperature adhesive tape is an excellent electrical insulator with good corrosion resistance, and its silicone adhesive maintains a strong bond throughout the full rated temperature range...

SKU: EC-RPA32311R

A high-precision real-time clock (RTC) module based on the DS3231 IC, designed to plug directly into a Raspberry Pi B+ (and compatible with Arduino). The DS3231 maintains accurate timekeeping with ±5 ppm accuracy (±0.432 seconds per day) across −40 °C to +85 °C, and includes a coin cell battery b...

SKU: AF-4807

An acrylic faceplate and hardware kit for the Adafruit MagTag. The kit includes two front plate options — a red arrow and a white cloud — plus a back plate and all the nylon mounting hardware needed for assembly. Takes just a few minutes with a Phillips screwdriver. Key Features Two Faceplate ...

SKU: AF-5134

THE REACTOR'S MELTING DOWN! GRAB THE FUEL CORE, JENNA, AND EVACUATE THE COMMAND CENTER! With this Rotating LED Warning Light with Adjustable Volume Buzzer Alarm, you can monitor and easily alert humanoids as to the status of a project, machine, or even if the bathroom is occupied!This alarm is ve...

SKU: PR-PIM373

The VL53L1X Time of Flight sensor breakout uses a low-power laser to measure distances with excellent accuracy and speed. With a detection range of 4 cm to 4 metres and up to 50 Hz sampling frequency, it's ideal for proximity sensing, presence detection, and collision avoidance on robots. This b...

SKU: AF-4202

Need some miniature indicators? We are big fans of these diffused LEDs. They are fairly bright, so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Now you can get a pack of 25 with 5 different colors Pack of 25 diffuse...

SKU: SF-SEN-12064

The HTU21D is a low-cost, easy to use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for a weather stations or humidor control systems. All you need is two lines for I2C communication and you’ll have relative ...

SKU: AF-302

Diffused 5mm tri-color LEDs with separate red, green and blue LED chips inside! Nice indicator, and fun to color-swirl. 60 degree viewing angle. We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct LEDs. These are Common-Anode type which means you connect on...

SKU: AF-1361

This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit. It's pressure-sensitive: squeezing it will reduce the resistance, so it's handy for making flexible sensors. And it's a lot less expensive than off-the-shelf pressure ...

SKU: AF-847

Need some big indicators? We are big fans of these huge diffused blue LEDs. They are really bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 diffused blue LEDs 10mm diameter 465-470nm wavelength 3....

SKU: SF-COM-11913

A green inverter connector cable for use with the INV133 electroluminescent inverter, bridging the gap between your inverter and ELastoLite panels. The 4.5-inch cable has bare wire leads that can be ironed directly onto ELastoLite connect patches for a clean, secure connection. ELastoLite is a w...

SKU: AF-780

Need some indicators? We are big fans of these diffused blue LEDs, as featured in the LoL shield. They are really bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 diffused blue LEDs 3mm diameter 4...

SKU: AF-5687

Here at Adafruit, we love discovering new and exotic glowing things. Like moths to the flame, we were intrigued by this 'chip on board' ultra-flexible RGB LED Strip with a whoppin' 630 SMT LEDs per meter (210 x RGB LEDs, with 3 in series per segment), soldered side-by-side and...

SKU: AF-301

Need some really bright LEDs? We are big fans of these clear blue LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 clear blue LEDs 5mm diameter 4...

SKU: PL-2739

The Pololu AltIMU-10 v5 is a compact inertial measurement unit (IMU) and altimeter that combines a gyroscope, accelerometer, magnetometer, and barometric pressure sensor on a single board. It provides ten independent measurements — pressure, 3-axis rotation, 3-axis acceleration, and 3-axis magnet...

SKU: SF-DEV-13735

Blink any color you need! Use the LilyPad RGB LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can produce a broad variety of colors. Each of the colors in the RGB LED are connected to one of the sew tabs on the board labeled R, G, and B.The color channels on ...

SKU: AF-576

Put a temperature meter anywhere with this very handy display. This panel meter displays the temperature of the attached waterproof 1% thermistor in °C. It does require a DC voltage to run, at 4.5-30VDC. It has reverse polarity protection in case you swap the power leads by accident. To use, sim...