All Products

SKU: SF-WRL-15663 · MPN: WRL-15663

Built around Espressif's ESP32-WROOM module, this Feather-compatible development board is a handy starting point for WiFi, Bluetooth and battery-powered IoT projects. The dual-core Xtensa 32-bit LX6 processor runs at up to 240MHz, with 16MB of embedded flash and 520KB of internal SRAM on hand for...

SKU: SF-WRL-17381 · MPN: WRL-17381

Built around Espressif’s ESP32-WROOM-32UE module, this Thing Plus board gives you a compact foundation for connected projects that need WiFi, Bluetooth and a flexible antenna setup. The onboard U.FL connector lets you attach a suitable external antenna for installations where a PCB antenna is not...

SKU: SF-WRL-25134 · MPN: WRL-25134

Build connected sensor nodes, data loggers and battery-powered IoT projects around Raspberry Pi’s RP2350 microcontroller. This Thing Plus board adds wireless connectivity, extra memory and the familiar Feather-compatible footprint in a compact development platform.The RP2350 can run two selected ...

SKU: SF-DD-27675 · MPN: DD-27675

This Thing Plus board is a wireless development platform built around the Raspberry Pi Foundation RP2350 microcontroller. It combines the familiar Thing Plus form factor with Qwiic expansion, a µSD card socket, USB-C, LiPo charging hardware and a fuel gauge for local or remote projects.The RP2350...

SKU: EC-ILM13103D

ThinkNode G3 is a high-performance, compact LoRaWAN gateway designed for IoT communications by Elecrow. It uses the ESP32-S3 dual-core processor and Semtech SX1262 transceiver, equipped with a 240MHz dual-core main control, integrated Bluetooth, WiFi and optional 4G modules(Not yet released), an...

SKU: EC-CIL13002M2

Elecrow ThinkNode-M2 is a high-performance LoRa signal transceiver. It uses the ESP32-S3 module as the main processor and supports Bluetooth. Users can easily configure and monitor the device through their mobile phones. M2 is pre-installed with Meshtastic firmware and equipped with an SX1262 wi...

SKU: EC-ILM13205D2-915

The Elecrow ThinkNode M5 is a high-performance LoRa communication device powered by the ESP32-S3 processor. Pre-installed with Meshtastic firmware and featuring the SX1262 wireless chip, it efficiently sends and receives LoRa signals for off-grid mesh networking. With its compact, integrated des...

SKU: EC-LMM15507D

This ThinkNode M7 is a high-performance gateway based on the ESP32-S3 module and LR1110 LoRa chip, deeply adapted for the LoRa protocol. The device features an Xtensa 32-bit LX7 dual-core processor with a clock speed of up to 240MHz, providing powerful computing capabilities. It also integrates 2...

SKU: AF-1891 · MPN: 1891

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value). We particularly like th...

SKU: AF-5729

Look, over there at that thing! Take it apart! You can now attack just about every kind of box or enclosure that needs undoing with this 9-piece screwdriver set. This kit is of fine quality and excels at disassembling games, phones, cameras, and other small portable electronic goodies.What drew u...

SKU: SF-COM-15350

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind you might find in one of those "talking greeting cards".

SKU: SF-COM-21311

A compact, thin speaker ideal for projects where space is tight. At just 28 mm in diameter and approximately 4 mm thick, it fits into enclosures and wearables where standard speakers won't. The pre-wired 180 mm cable terminates in a 2-pin JST connector for easy hookup. Key Features 28mm Diamet...

SKU: AF-3763 · MPN: 3763

We're keepin' it wheel with this one! Plastic gear-box motors (also known as 'TT' motors) are an easy and low cost way to get your projects moving. But we've noticed that there are not a lot of nice TT motor wheels to go along with them. This Thin White Wheel has solid...

SKU: SF-TOL-09317

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but soldering flat on a table works just fine. Then again, the desk is starting to loo...

SKU: PK-SN-392

This handy third hand tool helps hold small parts steady while you solder, inspect, glue or assemble detailed projects. It is well suited to electronics work, lab tasks, jewellery making and other precision jobs where an extra pair of hands makes life easier.The heavy iron base keeps the stand st...

SKU: LB-LS0299

This multifunctional third hand soldering stand combines adjustable crocodile clip clamps, LED lighting, and a dual magnifying lens to keep your hands free while soldering, assembling, or inspecting small components. The weighted base with a steel plate provides extra stability, and it can be po...

SKU: SF-TOL-18472 · MPN: TOL-18472

These threaded inserts are a handy way to add strong, reusable fixing points to a jig, fixture or machine wasteboard. Place a few exactly where you need hold-down points, or install them in a grid pattern to turn a wasteboard into a threaded table.Installation is straightforward: create a 9mm pil...

SKU: SF-ROB-20441

A 3-phase DC brushless DC motor has the unique capability of being both a high efficiency, high torque, very smooth motor, as well as the starting point for haptic feedback when combined with the appropriate sensor and motor control. For an excellent demonstration of what's possible with 3-phase ...

SKU: EC-RPA00273R

This handy Three Wire Display Stand is made for Raspberry Pi, but also can adapt to other tablet PC, such as iPad. It is great for general electronics & TFT holding. You can adjust the angle as you like. Features Fully adjustable Vinyl Coated Steel Wire that will not scratch furniture or disp...

SKU: DF-SEN0596 · MPN: SEN0596

##Introduction This carbon monoxide gas sensor differs from most gas sensors on the market as it does not provide specific gas concentration data. Instead, it detects whether the surrounding environment exceeds or falls below a fixed threshold. It operates on a wide voltage range of 5-24V, with h...