All Products

SKU: DF-SEN0144

The Sharp GP2Y1010AU0F is a compact optical dust sensor that uses an internal infrared LED and phototransistor arranged diagonally to detect fine particles in the air. The sensor outputs an analog voltage proportional to dust density, and its pulse pattern can distinguish between smoke and dust p...

SKU: LB-LR0214-20

The GP2Y0A41SK0F is a short range Sharp analog distance sensor. The detection range is 1.5″ to 12″ (4 cm to 30 cm). The shorter range gives you higher resolution measurements, and the lower minimum detection distance makes this sensor great for detecting very close objects. The distance is indica...

SKU: AF-1393

The 96x96 resolution SHARP Memory LCD is no longer made, but we have a higher-resolution 168x144 display available in the shop at https://www.adafruit.com/product/3502 The 1.3" SHARP Memory LCD display is a cross between an eInk (e-paper) display and an LCD. It has the ultra-low power usage of...

SKU: LB-LS1610

These handy little pliers are great for you electronic and 3D printing need.  Use them for trimming and twisting.Pack contains 1 x Nose Plier1 x Wire Plier1 x Diagonal Plier

SKU: JU-R-E196

Whether you're trans, gender diverse, non-binary, or an ally, these pins are for everyone. Wear them with pride to show your pronouns. There's no right or wrong way: There's only your way. This colourful, gold-backed, hard enamel lapel pin comes beautifully presented on a Jubly-Umph backing card...

SKU: AF-85

“How could something so simple be so useful?”  We heard once that in the 4th millenium B.C. some guy asked the person who invented the wheel that question.  The person who invented the wheel’s answer, we were told, was something like “well it’s not actually that simple - i...

SKU: PL-1242

The ShiftBar is a medium-power RGB LED controller featuring 10-bit digital brightness control on each color channel (over one billion colors). Multiple ShiftBar modules can be chained together and controlled from a single microcontroller to create large LED displays.

SKU: DF-DFR0072

At sometime or another you may run out of pins on your Arduino board and need to extend it with shift registers.  With this shift out module which is based on 74HC595. The datasheet refers to the 74HC595 as an "8-bit serial-in, serial or parallel-out shift register with output latches; 3-sta...

SKU: SF-COM-13699

The SN74HC595N is a simple 8-bit shift register IC. Simply put, this shift register is a device that allows additional inputs or outputs to be added to a microcontroller by converting data between parallel and serial formats. Your chosen microprocessor is able to communicate with the The SN74HC5...

SKU: LB-FIL-0143

We've finally found the best Sparkling Gold  PLA filament in Australia! This is a 1Kg reel of 1.75mm Sparkling Gold PLA (polylactic acid) plastic filament for 3D printing. PLA is a bioplastic and makes for a great general-purpose filament with smooth surface finish. This filament i...

SKU: AF-2940

These two Short Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your Feather ...

SKU: AF-3002

These two Short Male Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! These headers are particularly cute and tiny and are designed to match perfectly with our shorty female header kit for Featherwings. Note that you could ...

SKU: AF-4174

These three Short Female Headers alone are, well, lonely. But pair them with any of our ItsyBitsy boards, and you're in business! These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your ItsyBitsy project takes...

SKU: AF-1070

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.These sensors are easy to use, they are basically resistors that change value based on how much their flexed. If they're unflexed, the resistance is ...

SKU: AF-4173

These three Short Male Headers alone are, well, lonely. But pair them with our ItsyBitsy boards, and you're in business! These headers are particularly cute and tiny and are designed to match perfectly with our shorty female header kit for ItsyBitsy. Note that you could use normal header...

SKU: AF-5584

These two Short Plug / Male Headers alone are, well, lonely. But pair them with the Raspberry Pi Pico, and you're in business! These 2.54mm / 0.1" pitch headers are particularly cute and tiny and are designed to match perfectly with the Pico and our short socket headers. Note that yo...

SKU: AF-5585

These Socket Headers alone are, well, lonely. But pair them with the Raspberry Pi Pico, and you're in business!These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your Pico project takes up, but still ...

SKU: LS-LS7430

Upgrade your MicroBit with our Short USB-C to Micro USB data cable, measuring at just 30cm! This durable cable is perfect for connecting your MicroBit to a computer, power bank, or other device with a USB-C port. Transfer data quickly and efficiently, whether you're updating firmware or tran...

SKU: AF-1592

A set of 12 short alligator clip test leads for making quick temporary connections without soldering. Each lead has a vinyl-covered alligator clip on both ends, colour-coded across six colours for easy circuit identification. The short length minimises tangle on the workbench. Key Features 12-...

SKU: AF-5515

Stretch out your servo connections with this flexible servo to premium male header jumper cable. It has a 3-pin shrouded "male" connector to plug the servo into and then, 17cm later, three separated jumper wire ends that plug into a breadboard or some header.It's excellent for when you want ...