All Products

SKU: SF-WRL-00558

A large 2.4 GHz rubber duck antenna with 5 dBi gain and a reverse-polarity SMA (RP-SMA) connector. At 196 mm (7.7″) long, it provides significantly more range than smaller duck antennas — ideal when you need to push your wireless link further. Key Features 5 dBi Gain – Higher gain for extended...

SKU: SF-WRL-12569

This is the XBee WiFi Module with RP-SMA connector from Digi. XBee WiFi embedded RF modules provide simple serial to IEEE 802.11 connectivity. By bridging the low-power/low-cost requirements of wireless device networking with the proven infrastructure of 802.11, the XBee WiFi creates new wireless...

SKU: AF-1352

A simple 1-to-4 DC barrel jack splitter that lets you power four devices from a single DC power adapter. Features standard 5.5mm/2.1mm barrel connectors with rugged moulded construction. Plug your existing DC power supply into the input jack, and get four identical output plugs ready to connect ...

SKU: SF-WRL-18568

This SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm (compared to 100mm). We found that the extra 50mm makes all the difference when working with an enclosure...

SKU: SF-PRT-10288

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might be the simple solution.

SKU: SF-PRT-10287

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution.

SKU: AF-1351

A simple 2-way DC barrel jack splitter that lets you power two devices from a single power adapter. Plug in one standard 5.5mm/2.1mm DC barrel jack and get two identical outputs — perfect for powering multiple boards or accessories from a single supply. Key Features 1-to-2 Splitter – One DC ba...

SKU: AF-944

A 100 mm (4″) swivel dipole antenna with 2 dBi gain and an RP-SMA connector — the industry-standard fitting found on most WiFi routers and wireless modules. The swivel joint lets you angle the antenna for optimal signal direction. Key Features 2 dBi Gain – Omni-directional coverage for short-t...

SKU: SF-GPS-24114 · MPN: GPS-24114

The SparkFun GNSS L1/L5 Breakout - NEO-F10N, SMA is a standard precision GNSS board with meter-level positional accuracy. The NEO-F10N uses the L1/L5 bands instead of the more commonly seen L1/L2 bands. Utilizing the L5 band, the NEO-F10N delivers improved performance under challenging urban envi...

SKU: DF-FIT0110

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution. Wi...

SKU: SF-GPS-14987

This tri-band GNSS antenna is ideal for GPS L1, GLONASS L1, and Beidou B2 reception. At 45x45mm it is a large ceramic antenna with an incredible 38dB LNA gain.This antenna works well with the GPS-RTK providing reception of Beidou satellites where other more basic GPS antennas cannot. We’ve chosen...

SKU: SF-WRL-14875

A compact 1/4-wave rubber duck antenna for LoRa and other 860–960MHz communication. With a centre frequency of 915MHz and 2dBi gain, this 110mm antenna is ideal for space-constrained LoRa nodes where a smaller antenna is preferred. Specifications Frequency Range – 860–960MHz (centre 915MHz) G...