All Products

SKU: DF-TEL0115

LoRa Radio Module is a type of long range low data rate data radio modem based on Sx1276 from Semtech. It is a low-cost sub-1 GHz transceiver module designed for operations in the unlicensed ISM (Industrial Scientific Medical) and LPRD bands. Frequency spectrum modulation/demodulation, multi-...

SKU: SF-GPS-28139 · MPN: GPS-28139

The SparkPNT GNSS Flex Module delivers centimetre-level RTK positioning using the Quectel LG290P receiver with quad-band support (L1, L2, L5, E6/L6) and multi-constellation tracking across GPS, GLONASS, Galileo, BDS, QZSS, and NavIC. With a built-in NIC anti-jamming unit and 1,040 tracking channe...

SKU: DF-DFR0323

The Bluno Mega 2560 combines the ATmega2560 microcontroller with an integrated TI CC2540 Bluetooth 4.0 (BLE) module, bringing wireless communication to the Arduino Mega form factor. It supports wireless programming over BLE, Bluetooth HID, iBeacon, and serial pass-through — while remaining fully ...

SKU: AF-5709

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps over a two-wire differential bus. Only an SPI port and two pins (chip-select and ...

SKU: WS-23949

The USB to RS485/422 is an industrial-grade isolated converter designed for reliable and stable communication. Featuring an original FT232RL chipset and SP485EEN transceiver, it ensures fast, interference-free data transmission. The unit includes multiple protective circuits such as power isolati...

SKU: SF-BOB-10124

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount o...

SKU: DF-TEL0125

The FireBeetle LoRa Radio 868 MHz is a wireless transmission cover board for the DFRobot FireBeetle series, featuring the Semtech SX1276 LoRa transceiver with a built-in power amplifier. It supports LoRa long-range modulation as well as FSK, GFSK, and OOK modes, with a transmission range of up to...

SKU: EC-AP0500STK

AVRISP2.0 STK500 programmer help you download your codes into your controller or bootloader to your Arduino board, it communicates with PC via USB port, and it works with most of PC & notebook computers.Features It can support a wide range of ATMEL AVR microcontroller. It can works with AVR Studi...

SKU: WS-19979

The 2-Channel RS232 Module for Raspberry Pi Pico converts UART signals to RS232 and vice versa using the SP3232EEN transceiver. It plugs directly onto the Pico via the onboard female pin header — no wiring required. The module provides two independent RS232 channels with TVS and ESD diode protec...

SKU: LB-00053

A simple breakout board for XBee modules that brings all 20 pins out to standard 0.1″ (2.54 mm) dual-row headers. The 0.5″ spacing between header rows makes it breadboard DIP-friendly for easy prototyping. Key Features All 20 Pins Broken Out – Full access to every XBee pin 0.1″ Header Spacing...

SKU: SF-SEN-08606

A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Glove. I love the Nintendo Power Glove. It’s so bad! The resistance of the flex se...