All Products

SKU: DF-SEN0451 · MPN: SEN0451

This industrial Gravity kit measures electrical conductivity in aqueous solutions, helping you evaluate water quality by tracking dissolved content or salinity. It is suited to hydroponics, aquaculture and environmental water monitoring where long-running measurements are needed.The pro probe is ...

SKU: SF-WRL-15130

After years of popularity with the XBee Series 1 and XBee Series 2, we now have the XBee Series 3 which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 200ft indoor range, or ...

SKU: SF-WRL-13225

The SparkFun XBee Explorer Serial is an RS232 serial base unit for configuring and communicating with XBee modules. Compatible with all XBee modules including Series 1, Series 2.5, standard, and Pro versions. Simply plug in an XBee module, connect an RS232 cable, and gain direct access to the ser...

SKU: DF-TEL0020

This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontroll...

SKU: DF-DFR0274

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED strip. A built-in IR receiver enables remote control operation, and an on-board fuse...

SKU: SF-WRL-21636 · MPN: WRL-21636

The SparkFun Digi XBee® Development Board is designed to help you quickly and easily prototype low-power cellular IoT applications using the new Digi XBee 3 Low-Power LTE-M/NB-IoT, Digi XBee RR, and any existing through-hole Digi Xbee module. This board breaks out all the functionality of your XB...

SKU: DF-SEN0433

A digital vibration sensor module that detects vibration using an internal inductance coil. When vibration is detected, the module outputs a LOW signal and its on-board LED indicator lights up. Sensitivity is adjustable via a built-in potentiometer, and the wide 5–15 V power supply range makes it...

SKU: SF-WRL-15128

After years of popularity with the XBee Series 1 and XBee Series 2, we now have the XBee Series 3 which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 200ft indoor range, or ...

SKU: SF-WRL-15126

After years of popularity with the XBee Series 1 and XBee Series 2, we now have the XBee Series 3 which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 200ft indoor range, or ...

SKU: SF-WRL-15127

After years of popularity with the XBee Series 1 and XBee Series 2 Pro Modules, we now have the XBee Series 3 Pro which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 300ft i...

SKU: SF-WRL-11812

This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programm...

SKU: DF-DFR0327

The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...