All Products

SKU: SF-WRL-17841

A compact wide-band internal antenna covering 700–2700 MHz, suitable for 4G LTE, LoRa, BLE, and other RF applications. The FPC radiator element connects via a 100mm coaxial cable with an IPEX (u.FL equivalent) connector, and 3M adhesive backing makes it easy to mount inside enclosures and project...

SKU: DF-DFR0921

Has it ever happened to you that you spent a lot of time ascertaining a problem when making projects and finally found out it was just caused by loose wiring? Then, what you may need is a terminal block shield like this! The shield adopts terminal blocks to secure wires so as to make connections ...

SKU: SF-DEV-15442

The RedBoard Artemis ATP is affectionately called 'All the Pins!' at SparkFun. The Artemis module has 48 GPIO and this board breaks out absolutely every one of them in a familiar Mega like form factor. What's with the silkscreen labels? They're all over the place. We decided to label the pins as ...

SKU: AF-4718

The Adafruit SPI Non-Volatile FRAM Breakout provides 2 Mbit (256 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times wit...

SKU: AF-419

Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin, flexible membrane material with an adhesive backing (just remove the paper) so you can attach it to nearly anything. The keys are connected into a m...

SKU: AF-5793

This is a screen for advanced hackers who like the look of a nice, round TFT screen with tons of pixels. This massive 4" diagonal-sized display has 720x720 16-bit full-color pixels and is an IPS display, so the color looks great up to 80 degrees off-axis in any direction. The TFT driver is ST7...

SKU: SF-PRT-16279

These stackable headers are made to work with the SparkFun Qwiic Shield for Arduino Nano or any comparable shield to connect the shield with a Arduino Nano footprint. This set includes two 15-pin headers; the pins are spaced by 0.1". Each set of headers allows you to stack a Qwiic Nano shield ...

SKU: DF-DFR1026

This is a DC charging and discharging integrated module, with 5V normally open output, which is not affected by load access and has a maximum load current of 2A. It features 4 levels of charge/discharge electricity indication and button-controlled output. The module comes with a built-in power ma...

SKU: SF-DEV-16789

The SparkFun Qwiic Shield for Arduino Nano provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Arduino Nano board. The Qwiic shield connects the I2C bus (GND, 3.3V, SDA and SCL) on your Arduino Nano to four SparkFun Qwiic connectors (two horizontally and two ...

SKU: DF-DFR0032

Here is the simplest sound making module that you can use High/Low to drive it. Just change the frequency it buzz, you can hear different sound. It is widely used on your daily application, like PC, refrigerator,phones and so on. And you also can create many interesting interactive project w...

SKU: AF-67

A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and use the switch to control power. Key Features On/Off Switch – Conveniently co...

SKU: SF-WRL-15131

After years of popularity with the XBee Series 1 and XBee Series 2 Pro Modules, we now have the XBee Series 3 Pro which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 300ft i...