All Products
Showing 41-57 of 57 products · 3 unavailable products hidden
Sensor ambiental ELECFREAKS PlanetX BME280
·
ELECFREAKS PlanetX BME280 Environment Sensor is a combination sensor based on digital humidity, pressure, and temperature sensors. It is also able to calculate the altitude based on the air pressure value.Learn PlanetX BME280 Environment Sensor
Adafruit BMP585 Ported I2C / SPI Temperature and Pressure Sensor
·
The BMP585 from Bosch is a ported barometric pressure and temperature sensor featuring a tube attachment point for differential or remote pressure measurements. It delivers exceptional precision with altitude noise as low as 1 cm (0.08 Pa), making it one of the most precise pressure sensors in th...
Adafruit MS8607 Pressure Humidity Temperature PHT Sensor - STEMMA QT / Qwiic
The Adafruit MS8607 is a factory-calibrated 3-in-1 sensor that measures barometric pressure, relative humidity, and temperature over I2C. Made by TE Connectivity, this PHT (Pressure, Humidity, Temperature) sensor is a compact, all-in-one solution for weather stations, environmental monitoring, an...
Adafruit SCD-30 - NDIR CO2 Temperature and Humidity Sensor - STEMMA QT / Qwiic
The Adafruit SCD-30 is a true NDIR (Non-Dispersive Infrared) CO2 sensor that directly measures carbon dioxide concentration in ambient air, rather than estimating it from volatile organic compounds. With an integrated SHT31 temperature and humidity sensor, it provides comprehensive environmental ...
Adafruit SPI Non-Volatile FRAM Breakout - 2 Mbit / 256 KBytes - MB85RS2MTA
The Adafruit SPI Non-Volatile FRAM Breakout provides 2 Mbit (256 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times wit...
Adafruit PT100 RTD Temperature Sensor Amplifier - MAX31865
The Adafruit PT100 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter. It reads 2-, 3-, or 4-wire PT100 platinum resistance temperature detectors over SPI, delivering laboratory-grade temperature accuracy and repeatability that surpasses therm...
DHT11 basic temperature-humidity sensor + extras
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires careful timing t...
Adafruit SHT41 Trinkey - USB Temperature and Humidity Sensor
·
The Adafruit SHT41 Trinkey is a tiny USB A device that combines an ATSAMD21 microcontroller with a Sensirion SHT41 temperature and humidity sensor. Simply plug it into any USB A port on your computer and start reading environmental data — no wiring, soldering, or driver installation required. Th...
Adafruit PCT2075 Temperature Sensor - STEMMA QT / Qwiic
The Adafruit PCT2075 Temperature Sensor is a precise, affordable I2C temperature sensor and a drop-in replacement for the classic LM75. With an 11-bit ADC (compared to the LM75's 9-bit), it delivers finer temperature resolution. Three-state address pins allow up to 27 sensors on a single I2C bus ...
Adafruit LPS35HW Water Resistant Pressure Sensor
The Adafruit LPS35HW is a water-resistant barometric pressure and temperature sensor from ST. The sensing element is housed in a ceramic package with waterproof gel protection, making it safe to use in damp and humid environments like outdoor weather stations. With 24-bit pressure data and 16-bi...
Fermion: SHT40 Temperature & Humidity Sensor (Breakout)
The SHT4X is the 4th generation digital temperature and humidity sensor from Sensirion. In line with Sensirion’s industry-proven humidity and temperature sensors, the SHT40 offers consistent high accuracy within measuring range. The SHT40 sensor covers a humidity measurement range of 0 to 100%RH ...
Adafruit Grand Central M4 Express featuring the SAMD51
The Adafruit Grand Central M4 Express is a powerful development board built around the Microchip ATSAMD51P20 — a 120 MHz Cortex M4 processor with hardware floating point, 1 MB Flash, and 256 KB RAM. In the familiar Arduino Mega form factor, it brings 70 GPIO pins, dual DACs, 15 analog inputs, 8 M...
Adafruit DPS310 Precision Barometric Pressure / Altitude Sensor - STEMMA QT / Qwiic
The Adafruit DPS310 is a high-precision barometric pressure and altitude sensor from Infineon, mounted on a breakout board with STEMMA QT / Qwiic connectors for solderless I2C wiring. It delivers ±1 hPa absolute accuracy and up to ±0.002 hPa relative precision in high-precision mode — equivalent ...
Octopus BME280 Pressure Sensor
Octopus BME280 Pressure Sensor is an electric brick, which has integrated temperature sensor, air pressure sensor and humidity sensor onboard. We can use it to measure humidity, temperature and air pressure, or even to calculate the altitude according to the measured air pressure. Features Low...
Adafruit ATSAMD09 Breakout with seesaw
The Adafruit ATSAMD09 Breakout with seesaw is a versatile I2C peripheral board built on the Adafruit seesaw framework. Seesaw is a near-universal converter that lets you add GPIO, ADC, PWM, and more to any I2C-capable microcontroller or single-board computer — all over a simple I2C connection. R...
Adafruit PT1000 RTD Temperature Sensor Amplifier - MAX31865
The Adafruit PT1000 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter, configured for PT1000 platinum resistance temperature detectors. It reads 2-, 3-, or 4-wire PT1000 sensors over SPI, delivering laboratory-grade temperature accuracy and r...
Adafruit ICM-20649 Wide Range ±30g ±4000dps 6-DoF IMU
The Adafruit ICM-20649 breakout features a wide-range 6-DoF IMU capable of measuring up to ±30g acceleration and ±4000°/s gyroscope rotation — roughly double the range of standard IMUs. When typical ±16g accelerometers and ±2000°/s gyros aren't enough, this sensor delivers the extended measuremen...
