All Products

SKU: AF-6153 · MPN: ADA6153

USB-C Panel Mount Cable – Compact & Easy InstallationThis USB Type-C panel mount cable is perfect for adding a USB-C connection to your project enclosure. The compact panel-mount side features a USB-C jack, while the other end provides power, ground, D+/D-, and CC1/CC2 lines for quick integration...

SKU: SF-DEV-16526

The Alchitry Cu is an affordable FPGA development board featuring the Lattice iCE40 HX with 7,680 logic cells. This SparkFun version adds a Qwiic connector for easy I2C sensor and actuator integration. It can be programmed using entirely open-source tools via Project IceStorm. The Cu provides 79...

SKU: DF-KIT0194

This expansion ecosystem transforms the UNIHIKER M10 single-board computer into a fully functional AIoT development station. By leveraging the modular DFRobot Gravity interface, the kit allows for the seamless integration of over 16 distinct environmental monitors, vision peripherals, and intera...

SKU: SF-SEN-29259 · MPN: SEN-29259

Built around the Allegro ACS37800, this Qwiic power meter lets your project monitor voltage and current at the same time over I2C. It is designed for higher-demand loads such as 3D printers, UAVs and solar panels, with voltage monitoring up to 60VDC and current sensing up to 30A.The ACS37800 uses...

SKU: DF-FIT0449

INTRODUCTION This speaker module is based on the 8002 speaker amplifier IC. It can be used as a buzzer and also play high quality audio. Volume output is controlled via the potentiometer. The module has various advantages (e.g. a compact footprint, simple in...

SKU: DF-SEN0474

This is a sensor that detects hydrogen chloride concentration and supports three output modes: analog, I2C, and UART. The probe has been calibrated at the factory, which can quickly and accurately measure the concentration of hydrogen chloride in the environment. Can be widely used in the detecti...

SKU: EC-WWF2232USR

This Serial WiFi module is you best choice for you to connect your application to the internet. It is a complete ultra low power embedded TCP/IP solution. It is a standalone, embedded wireless 802.11b/g networking module. It incorporates a 2.4GHz radio, processor, TCP/IP stack, power management t...

SKU: DF-DFR0645-G

The Gravity 4-Digital LED Segment Display Module features a bright green 7-segment display with four digits, perfect for showing numbers, time, sensor readings, and other data in your projects. It communicates over I2C for simple two-wire connectivity with Arduino, Raspberry Pi, and other microco...

SKU: DF-DFR0327

The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...

SKU: DF-DFR1083 · MPN: DFR1083

##Introduction The Arduino Portenta C33 is a streamlined module that offers the high performance of the Arduino Portenta family at a lower price point, thanks to optimizations and streamlined features. Ideal to developing cost-effective, real-time applications, the Portenta C33 features the ARM® ...

SKU: LB-ETEXTILELED-Y

This is a simple single unit YELLOW E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. They’re even washable (with special care)!These are a thicker PCB than the Sparkfun Lilypad LEDs

SKU: DF-DFR0557

The Gravity I2C LCD1602 is a 16×2 character LCD display module from DFRobot's Gravity series, redesigned with a clean modern look and simplified I2C interface. It eliminates the need for contrast adjustment, retains backlight control, and is compatible with both 3.3 V and 5 V systems — making it ...

SKU: EC-DTS01559G

This is a GPIO expansion board for Micro: bit, it’s convenient to operate. It can be inserted the expansion board directly into the Micro: bit, and this expansion board can be cascaded.SpecificationsSize: 64 x 37 x 12 mmPackage listMicro: bit GPIO expansion board x 1

SKU: DF-DFR0031-W

Piranha LED light module, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can...

SKU: FT-HUMID

Measure temperature and relative humidity with this simple, Arduino-compatible sensor module based on the DHT22. With just three connections (GND, power, and data), you can read both temperature and humidity from a single I/O pin on your microcontroller. An Arduino library is available to make in...

SKU: DF-FIT0416

Introduction This product converts from USB output to TTL output, supports three levels, facilitates communication between PC and serial port, does not need an external crystal oscillator, has high stability and strong anti-interference. Specification VCC output: 5V/3.3V/1.8V TTL output: 5...

SKU: AF-6058 · MPN: ADA6058

Add programmable colour to patios, balconies, displays and outdoor-style decorations with this bulb strand fitted with NeoPixel RGB LEDs. Each strand has 20 cafe-style bulbs, and each bulb is individually addressable so you can create rainbows, chases, fades and other effects using a NeoPixel/WS2...

SKU: LB-LS0824

The IO:bit is a compact expansion board for micro:bit that breaks out all I/O pins to standard headers while adding a built-in miniature buzzer. It features Lego-compatible mounting holes for integration with KittenBot and other building projects. Key Features Plug and Play – Edge connector fo...

SKU: DF-DFR0461

Good news everyone! We have a new member to the Gravity family - The Flexible 8x8 RGB LED Matrix! This module is a square panel with a soldered XH2.54 3-pin interface with pin mappings that perfectly match the Arduino I/O expansion shield. This flexible 8x8 RGB full-color LED matrix module...

SKU: SF-GPS-23814 · MPN: GPS-23814

The u-blox ANN-MB1 is a multi-band active GNSS antenna supporting L1, L5, E5a, B2a, and NavIC frequency bands. Designed for high-precision positioning applications, it pairs directly with the u-blox F9 platform (NEO-F9P, ZED-F9P, ZED-F9T) and other multi-band GNSS receivers. The antenna features...