All Products

SKU: AF-945

A 200 mm (8″) swivel dipole antenna with 5 dBi gain and an RP-SMA connector — the industry-standard fitting found on most WiFi routers and wireless modules. The higher gain compared to the 2 dBi version extends range at the cost of a larger form factor. The swivel joint lets you angle the antenna...

SKU: SF-WRL-00558

A large 2.4 GHz rubber duck antenna with 5 dBi gain and a reverse-polarity SMA (RP-SMA) connector. At 196 mm (7.7″) long, it provides significantly more range than smaller duck antennas — ideal when you need to push your wireless link further. Key Features 5 dBi Gain – Higher gain for extended...

SKU: AF-1864

This is a great connector for anyone doing RF work, when an SMA connector is required. It hugs the edge of a "half thickness" 0.031" thick PCB (or thinner!) and 'launches' off of the edge. We like these for their ease of soldering and low profile. Mates with any SMA plug, we also have an SMA to R...

SKU: AF-1865

This is a great connector for anyone doing RF work, when an SMA connector is required. It hugs the edge of a standard 0.063" thick PCB and 'launches' off of the edge. We like these for their ease of soldering and low profile. Mates with any SMA plug, we also have an SMA to RP-SMA in case your ant...

SKU: SF-WRL-18569

This RP-SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm (compared to 100mm). We found that the extra 50mm makes all the difference when working with an enclos...

SKU: AF-944

A 100 mm (4″) swivel dipole antenna with 2 dBi gain and an RP-SMA connector — the industry-standard fitting found on most WiFi routers and wireless modules. The swivel joint lets you angle the antenna for optimal signal direction. Key Features 2 dBi Gain – Omni-directional coverage for short-t...

SKU: SF-WRL-14875

A compact 1/4-wave rubber duck antenna for LoRa and other 860–960MHz communication. With a centre frequency of 915MHz and 2dBi gain, this 110mm antenna is ideal for space-constrained LoRa nodes where a smaller antenna is preferred. Specifications Frequency Range – 860–960MHz (centre 915MHz) G...

SKU: AF-5474

A comprehensive set of 30 barrel jack plug adapters that convert a standard 5.5mm / 2.1mm DC jack to a wide variety of other tip sizes. Perfect for powering devices that use non-standard barrel connectors from your existing DC power supplies, USB-C to DC cables, or battery packs. Each adapter pl...

SKU: SF-WRL-09145

This is a 4" connector cable that interfaces U.FL RF connectors to regular SMA connectors. Documents: Datasheet RF Connector Buying Guide

SKU: WS-21708

A 5G cellular HAT for Raspberry Pi built around the SIM8202G-M2 module on Qualcomm's Snapdragon X55 platform. Supports 5G NSA and SA networking alongside 4G and 3G fallback, plus multi-constellation dual-band GNSS positioning. Connect via USB 3.1 to a Raspberry Pi, Jetson Nano, or PC for high-spe...

SKU: AF-2897

A simple adapter that sits inside a 5.5 / 2.5 mm DC barrel jack, allowing you to use a standard 5.5 / 2.1 mm barrel plug with it. Just insert the adapter into the device's 2.5 mm jack, then plug in your 2.1 mm power supply as normal. Key Features 2.5 mm to 2.1 mm Conversion – Adapts a 2.5 mm I...

SKU: AF-4642

This is a great connector for anyone doing RF work, when a right angle SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground.Mates with ...

SKU: SF-CEL-00290

A Quad-band antenna for embedded cellular devices. This antenna will allow you to connect your cellular module to the outside world. Operates on four frequencies. Comes with a 3M adhesive backing for mounting. Standard male SMA terminated. Key Specifications: Quad-band: 850/900/1800/1900MHz a...

SKU: DF-FIT0219

The Interface Cable SMA to U.FL is a connector cable that interfaces U.FL RF connectors to regular SMA connections. APPLICATIONS Connect Standard SMA Connector for SIM 908 GPS/GPRS/GSM Shield For Arduino SPECIFICATIONS Frequency Range:DC~12.4GHz VSWR:≤1.10+0....

SKU: AF-4287

A push-fit DC barrel jack adapter that converts a 3.5/1.1 mm DC plug to the standard 5.5/2.1 mm DC barrel jack format. Simply push it onto the smaller plug until it clicks into place — no soldering or tools required. Key Features Click-Fit Connection – Push onto the plug until it clicks secure...

SKU: WS-8781 · MPN: 8781

Enhance your positioning accuracy with our high-performance GPS External Antenna, designed with an integrated amplifier and superior ceramic technology for optimal signal capture and amplification. Suited for a multitude of positioning and navigational applications, this antenna is the perfect ac...

SKU: SF-WRL-09143

A 900/1800MHz dual-band duck antenna with 2dBi gain and an RP-SMA connector. Well suited for XBee 900MHz modules and other 900MHz radio applications. 50-ohm impedance, 105mm long. Specifications Frequency – 900/1800MHz dual-band Gain – 2dBi Connector – RP-SMA Impedance – 50 ohm Length – 10...

SKU: DF-FIT0957 · MPN: FIT0957

The IPEX4 to SMA Female Connector Cable is a 200 mm adapter designed for single-board computers equipped with an IPEX4 (MHF4) wireless interface, including the LattePanda 3 Delta, LattePanda 2 Alpha, and LattePanda 2 Delta. It converts the onboard IPEX4 connector to a standard SMA female port (ex...

SKU: SF-GPS-24114 · MPN: GPS-24114

The SparkFun GNSS L1/L5 Breakout - NEO-F10N, SMA is a standard precision GNSS board with meter-level positional accuracy. The NEO-F10N uses the L1/L5 bands instead of the more commonly seen L1/L2 bands. Utilizing the L5 band, the NEO-F10N delivers improved performance under challenging urban envi...

SKU: SF-WRL-20856

A 433MHz antenna that utilizes an SMA connector and is 200mm long with a gain of 2dBi. Comes with the frequency laser printed on the antenna. Features: Frequency: 433MHz Gain: 2dBi Antenna Length: 200mm Connector: SMA Plug Articulating Base Documents: Technical Drawing