All Products

SKU: AF-184

Build your own breadboard-friendly adjustable power supply with this soldering kit. Based on the MIC2941 low-dropout regulator, it provides a guaranteed 1.25A output with only 40–400 mV dropout — far better than the LM317's typical 1.25–2.0V. This means you can generate 3.3V from as low as 3.7V i...

SKU: SF-COM-09806

There are lots of trimpots out there. Some are very large, some so small they require a screwdriver. Here at Little Bird, we just needed a simple one that worked. This 10K trimmable potentiometer has a small knob built right in and it’s breadboard friendly to boot! Perfect for your next LCD ...

SKU: SF-COM-29199 · MPN: COM-29199

This adjustable dual-gang potentiometer gives you two linked variable resistors on a single shaft, making it handy for interfaces where two channels need to move together. Turn the shaft and the resistance changes, so it can be used to create a variable voltage for an analogue input.Connect VCC t...

SKU: AF-1789

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-poin...

SKU: LB-LS2921

Comes as a standard 10K ohm linear potentiometer with 0.1" spacing it works great for  prototyping. It has a nice feel, tweaking it is quite satisfying.These are used on the crack the code shield.1 x Potentiometer with Built In Knob - 10K ohm

SKU: SF-COM-11620

A compact linear-taper slide potentiometer rated at 10 kΩ and 0.1 W. This small slider features solder tab connections, a 20 mm travel distance, and two mounting holes for easy installation. Key Features Linear Taper – Smooth, proportional resistance change across the travel range Solder Tab ...

SKU: LB-SOLAR-M

A compact micro solar panel rated at 1.5 V and 400 mA (0.65 W peak), fitted with pre-soldered male jumper wires for direct breadboard use. Its small 80×60 mm form factor makes it easy to integrate into DIY solar projects and prototyping setups. Key Features 1.5 V / 400 mA Output – 0.65 W peak ...

SKU: PI-COM-B005

580 resistors (29 values, 20 pieces of each) go into this great starter pack (or refill!) with a wide range of useful values. The kit contains 20 each of:10Ω22Ω47Ω68Ω100Ω120Ω150Ω180Ω220Ω270Ω330Ω470Ω560Ω680Ω1kΩ1.2kΩ1.5kΩ1.8kΩ2.2kΩ2.7kΩ3.3kΩ4.7kΩ5.6kΩ6.8kΩ8.2kΩ10kΩ22kΩ47kΩ100kΩ Rated for&nb...

SKU: SF-BOB-11722

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you’r...

SKU: AF-3482

This Panel Mount 10K Dual Logarithmic Potentiometer w/ On-Off Switch is a two-in-one; you get a dual-ganged potentiometer and an on-off switch. For the potentiometer-half, you've got a dual standard log-taper 10Kohm potentiometer, with a grippy shaft. It's smooth and easy to turn, bu...

SKU: LB-LR0589-YELLOW

A 12 mm panel-mount momentary push button with a smooth dome-shaped cap in yellow. Normally open — pressing the button closes the contacts. The dome design provides a satisfying tactile feel and sits flush with the panel surface. Key Features Momentary Action – Normally open, closes on press ...

SKU: AF-4219

This 75mm slide potentiometer is a linear 10KΩ pot with a smooth, satisfying action and an included grippy plastic knob with a white position marker. Use it as a voltage divider, input control, or anywhere you need a visual, tactile slider interface. The three solder legs are compatible with bre...

SKU: AF-3481

A panel-mount 10 kΩ logarithmic potentiometer with an integrated on/off switch. The logarithmic taper is designed for audio volume control — resistance increases on a curve that matches how the human ear perceives loudness, giving smooth and natural volume adjustment from quiet to full. The buil...

SKU: AF-4272

Slip slidin' away Slip slidin' away You know the nearer your resistance The more you're slip slidin' awayIf you're tired of the regular-old-twisty potentiometers we carry, why not slide over and try this slide pot? Most famously used on mixers and the transporter control panel on S...

SKU: AF-5093

Here's a new addition to our rotary-potentiometer-knob family. This knob has a nice soft-touch feel with an arrow on it, and its much 'slimmer' than the skirted knob we have been using, so good for compact layouts.Note: This is just the knob. We have a breadboard-friendly rotary encoder here...

SKU: SF-COM-28384 · MPN: COM-28384

A compact thumbwheel potentiometer for adding analog control to your projects. The ergonomic wheel design allows for easy adjustment with one finger, making it perfect for volume controls, parameter adjustment, and user interfaces. Connect VCC to one outer pin, GND to the other, and the center p...

SKU: LB-50K

This 50KΩ single-turn potentiometer provides smooth linear (Type B) resistance adjustment, making it ideal for volume controls, brightness adjustments, and analogue input on Arduino and other microcontroller projects. The knurled shaft accepts standard potentiometer knobs for easy panel mounting....

SKU: SF-COM-29391 · MPN: COM-29391

This black 25mm potentiometer knob is a simple, sturdy control knob for adding a clean finish to panel-mounted pots and other compatible controls.It slides onto the potentiometer shaft and uses a key lock to help it hold tightly for a strong fit. The main body is metal with a plastic insert, and ...

SKU: PL-2739

The Pololu AltIMU-10 v5 is a compact inertial measurement unit (IMU) and altimeter that combines a gyroscope, accelerometer, magnetometer, and barometric pressure sensor on a single board. It provides ten independent measurements — pressure, 3-axis rotation, 3-axis acceleration, and 3-axis magnet...

SKU: AF-844

These large 10mm diffused green LEDs provide bright, wide-angle visibility that's easy to see even in daylight. The diffused lens spreads light evenly for a clean glow from any viewing angle, making them ideal as status indicators and display elements. Breadboard compatible for easy prototyping. ...