All Products

SKU: EC-SEA0001T

The Crowtail Starter Kit for Arduino is a beginner-friendly electronics kit built around the Crowduino Uno-SD board and the Crowtail modular connector system. With 22 plug-and-play modules and over 20 guided tutorials, it provides a structured introduction to Arduino programming and electronics —...

SKU: EC-AMS320240TFT

The 2.8" TFT Touch Shield V4.3 is an Arduino-compatible display shield featuring a 240×320 colour LCD with a resistive touchscreen and onboard SD card socket. It communicates over SPI, keeping pin usage low and leaving more pins available for other components. Driven by the ILI9341 controller, t...

SKU: EC-SEA0002T

The Crowtail Advanced Kit for Arduino is a comprehensive STEAM education kit containing 22 electronic modules and a Crowduino Uno SD board. With plug-and-play Crowtail connectors, no soldering or complex wiring is required — simply connect modules to the base shield and start programming. The ki...

SKU: EC-CRF1356KIT

This RFID kit includes a 13.56M RF reader module, which use the RC522 IC, plus 2 S50 RFID cards to help you learn and add the 13.56 MHz RF transition to your project. The MF RC522 is a highly integrated transmission module for contactless communication at 13.56 MHz, it supports ISO 14443A/MIFARE ...

SKU: EF-EF08180

ElecFreaks Micro:bit Starter Kit is designed for people who is at the door step of learning electric circuit and programming knowledge. The kit has provided some basic electronic components like LED, button, buzzer, temperature sensor , steering engine and motor etc.. You can not only learn basic...

SKU: PL-1125

A compact, inexpensive brushed DC motor with a 120:1 plastic reduction gearbox, well suited for small robot builds. The motor is rated for 4.5V but runs comfortably in the 3–6V range. The gearbox output shaft is a 3mm D-shape, offset from and parallel to the motor shaft. A built-in safety clutch ...

SKU: LB-LR0064

The KnockOffDuino® Uno is functionally the same as the Arduino Uno R3 at a fraction of the cost. It is the Arduino for beginners and 100% Uno compatible, however it uses the CH340G usb to serial chip instead of the 16u2/8u2 found in the official Arduino Uno R2/R3 so instead of the Arduino Uno ...

SKU: LB-LS6618

A compact 68-key wired mechanical keyboard with RGB backlighting, designed for gaming and everyday use. The space-saving layout fits comfortably on any desk while retaining all essential keys plus multimedia controls via laser-engraved function keys. USB plug-and-play with a 1.7 m cable — just c...

SKU: DF-DWG0003

A frosted milky-white acrylic base plate for the Arduino UNO and Leonardo. The base mounts underneath the board using nylon standoffs, protecting the underside from contact with work surfaces and giving your setup a clean, professional look. Made from high-quality double-sided frosted acrylic wi...

SKU: EC-CCC12311K

A set of stackable female headers for Arduino UNO and compatible boards. The extended contact length clears the USB-B connector, making them ideal for stacking multiple shields. Details Compatibility – Arduino UNO, Arduino Pro, Arduino Mega Pin Spacing – 0.1″ (2.54 mm) Type – Stackable (exte...

SKU: PL-1120

A 200:1 plastic gearmotor with a 90-degree output shaft, offering a compact and affordable solution for small robot designs. The low-current brushed DC motor is well-suited for use with common motor drivers, and the recommended operating voltage range is 3–12V. The gearbox is fully enclosed and ...

SKU: DF-DFR0181

This is the new Arduino Uno Rev 3. In addition to all the features of the previous board, the arduino Uno Rev 3 now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linu...

SKU: DF-DFR0274

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED strip. A built-in IR receiver enables remote control operation, and an on-board fuse...

SKU: SF-DEV-11224

This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf fil...

SKU: PL-1121

A 120:1 plastic gearmotor with a 90° output shaft — the output is perpendicular to the motor axis, making it a compact choice for small robot designs where side-mounted wheels or mechanisms are needed. The enclosed gearbox and low-current brushed DC motor run on 3–12V, with a built-in safety clut...

SKU: DF-DFR0216-R

This DIN Rail Mount Bracket provides quick and easy mounting for Arduino, which allows you to conveniently build up your Arduino-related projects. Made of high-quality PVC material, it is durable and fireproof, and well suitable for the boards like UNO R3 and Leonardo. Application Dimension...

SKU: SF-DEV-13975

At SparkFun we use many Arduinos and we’re always looking for the simplest, most stable one. Each board is a bit different and no one board has everything we want, so we decided to make our own version that combines all our favorite features. The SparkFun RedBoard combines the simplicity of the U...

SKU: SF-PRT-11417

These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin, 1 10-pin and 1 6-pin), enough to connect a shield t...

SKU: AF-6194 · MPN: ADA6194

A warm-white LED filament shaped as the letter "D", made from COB (chip on board) LEDs — the same technology found in Edison-style LED bulbs. Dozens of micro LED diodes are bonded onto a thin metal backing and coated in silicone, producing a bright, uniform glow from both sides. Lightweight and ...

SKU: AF-6206 · MPN: ADA6206

A warm-white LED filament shaped as the letter "O", made from COB (chip on board) LEDs — the same technology found in Edison-style LED bulbs. Dozens of micro LED diodes are bonded onto a thin metal backing and coated in silicone, producing a bright, uniform glow from both sides. Lightweight and ...