All Products

SKU: AF-3551

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plen...

SKU: AF-4170

A 16-pin (2×8) IDC ribbon cable with keyed connectors on both ends, 305mm (12") long. The 0.05" pitch ribbon cable connects to standard 2×8 0.1" × 0.1" IDC headers. Pin 1 is marked with a white stripe along the cable edge. Key Features 16 Pins (2×8) – Standard IDC ribbon cable layout 305mm (1...

SKU: SF-CAB-10647

Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness.This is a 15ft. length of 10-wire ribbon cable. Check the related products below for crimp-on connector...

SKU: AF-3563

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable...

SKU: AF-2258

The Adafruit Raspberry Pi B+ / Pi 2 / Pi 3 Case is a durable polycarbonate enclosure with a smoke-tinted base and clear top. Designed by Mike Doell, it offers a clean, professional look while keeping your Pi protected and fully accessible. The case features slim openings for all cables, a bevell...

SKU: AF-2359

The Adafruit Raspberry Pi A+ Case is a slim, durable polycarbonate enclosure designed specifically for the Raspberry Pi Model A+. With a smoke-tinted base and clear top, it offers a clean, professional look while keeping your Pi protected and accessible. Designed by Mike Doell, the case features...

SKU: AF-3562

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable...

SKU: AF-3561

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable...

SKU: PI-RPI-020

The Official Raspberry Pi Zero Case is designed to fit both the Pi Zero and Pi Zero W. It ships with three interchangeable lids so you can configure it for different use cases: a plain lid for a clean finish, a GPIO lid for header access from above, and a camera lid with a short ribbon cable for ...

SKU: SF-PRT-10651

These 2x3 crimp connectors can be snapped onto 6-wire ribbon cable to make your own cable assemblies and keep your connections organized. Simply press the connector onto your ribbon cable, no soldering required, which makes it easy to add as many mid-cable connectors as you need. Check the relate...

SKU: SF-PRT-08535

This 2×5 (10-pin) IDC ribbon cable with 2.54 mm pitch connectors is commonly used for AVR ISP programming and general-purpose communication between boards. The cable is 6 inches (approximately 15 cm) in length. Key Features 10-Pin (2×5) – Standard AVR ISP programming pinout IDC Connectors – K...

SKU: AF-3252

The Adafruit Raspberry Pi Zero Case is a compact two-piece polycarbonate enclosure that protects your Pi Zero while keeping all ports accessible. Designed by Mike Doell, it features a sleek black base and clear top that snap together without screws. The case provides slim openings for mini HDMI,...

SKU: AF-4377

Here is an updated, excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say hello to the improved SmartiPi Touch 2 which has a ton of new goodies like Pi 4 compatibility, various front-pieces for adding LEGO brick compatibility, and...

SKU: AF-3649

The 64×64 RGB LED Matrix with 2.5mm pitch packs 4096 bright RGB LEDs into a compact, ultra-high-density panel. With the tightest pixel spacing in the 64×64 range, this panel produces sharp, detailed images ideal for close-up indoor viewing. This panel uses a non-standard 5-address (ABCDE) multip...

SKU: DF-FIT0953 · MPN: FIT0953

##Introduction This product is a carefully selected cable designed for Type-C port conversion on UNIHIKER M10. It is made of silicone material and features a flat, flexible ribbon cable design. With its ultra-thin and mini size, it maximizes space-saving during project development.Note: Please ha...

SKU: AF-1957

A set of 20 premium male-to-male jumper wires in a ribbon cable strip, each 150 mm (6") long. The wires feature 0.1" (2.54 mm) male header contacts on both ends and come in 10 rainbow colours (2 of each). Pull individual wires from the ribbon as needed, or keep them together for organised wire ha...

SKU: DF-FIT0299

This kit includes PHR-2, PHR-3 and PHR-4 housing (20 units each), through-hole type shrouded header (20 units each) and crimp contact (100 units). SPECIFICATIONS Pitch:2.0mm ((0.079")) Current rating:2A AC,DC (AWG #24) Voltage rating:100V AC,DC Temperature range: -25°C to +85°C (including temper...

SKU: AF-4104

If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version i...

SKU: SF-PRT-21328 · MPN: PRT-21328

This 10-position right-angle terminal block header is made for secure, pluggable wire-to-board connections on a PCB. Solder it directly to your board and use it as the receptacle for a removable screw terminal block.It is well suited to I/O signals and power lines that may need to be disconnected...

SKU: AF-4108

A straight USB Type C male plug designed for building custom USB cables with DIY ribbon cable kits. Attach this plug to one end of a compatible ribbon cable using the flex cable clip — no soldering required. Mix and match different USB plug types on each end to create the exact cable you need. K...