All Products

SKU: AF-815

The Adafruit 16-Channel PWM/Servo Driver uses the PCA9685 chip to provide 16 channels of 12-bit PWM output over I2C. With a built-in clock, the driver runs independently — no need to continuously send signals from your microcontroller. Ideal for controlling servos, LEDs, or any PWM-driven device....

SKU: AF-1411

The Adafruit 16-Channel PWM/Servo Shield brings PCA9685-based servo and PWM control to any Arduino in a convenient shield format. Using only I2C (SCL and SDA), the shield provides 16 channels of 12-bit PWM output with a built-in clock — no continuous signal from your microcontroller needed. Up t...

SKU: AF-2327

The Adafruit 16-Channel PWM/Servo HAT adds precision servo and PWM control to your Raspberry Pi. Using the PCA9685 I2C PWM controller, it drives up to 16 servos or PWM outputs simultaneously with 12-bit resolution — completely free-running with no Pi processing overhead. Up to 62 HATs can be sta...

SKU: AF-3416

The Adafruit 16-Channel PWM/Servo Bonnet adds precision servo and PWM control to your Raspberry Pi. Using the PCA9685 I2C PWM controller, it drives up to 16 servos or PWM outputs simultaneously with 12-bit resolution — completely free-running with no Pi processing overhead. Up to 62 bonnets can ...

SKU: DF-FIT0731

NOTE: This product compatible with Raspberry Pi 3 Model B+, Raspberry Pi 4 Model B, and Jetson Nano.              Not compatible with Raspberry Pi 400, Raspberry Pi Pico and Raspberry Pi Compute Module 4.This is a 2-DOF pan-tilt hat based on Raspberry Pi 40PIN ...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: AF-2928

The 8-Channel PWM or Servo FeatherWing adds 8 channels of 12-bit PWM output to any Adafruit Feather board via I2C. It uses an onboard PWM driver with a built-in clock, so it runs independently without tying up your microcontroller — unlike the TLC5940 family, no continuous signal is needed. The ...

SKU: AF-1438

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...

SKU: AF-3093

The Adafruit CRICKIT for Circuit Playground Express is a robotics and electronics driver board that bolts directly onto a Circuit Playground Express. It adds motor drivers, servo outputs, capacitive touch inputs, NeoPixel control, and an audio amplifier — all managed over I2C via the Adafruit see...

SKU: ON-SERVOEXP

Add 16 independent PWM outputs to your Onion Omega2 for controlling servos, DC motors, and LED brightness. The onboard 3-pin connectors let you plug in standard servos directly – no breadboard or extra wiring needed. The built-in oscillator generates free-running PWM signals from 24Hz to 1526Hz....

SKU: SF-DEV-21326 · MPN: DEV-21326

This compact MicroMod processor board adds an STM32F405 to a compatible MicroMod Carrier Board, giving your project an ARM® Cortex®-M4 32-bit RISC core in a small, swappable M.2 module.The bevelled edge connector keys into the MicroMod M.2 socket and is secured with the screw supplied with MicroM...

SKU: DF-DFR0604

The IO Expansion HAT adds digital, analogue, I2C, PWM, UART, and SPI ports to the Raspberry Pi Zero and Zero W. An on-board STM32F030 MCU provides 8-channel 12-bit ADC and PWM output, communicating with the Raspberry Pi via I2C for convenient analogue input reading and servo control. Digital por...

SKU: SF-ROB-18648

The Arducam Upgraded Camera Pan Tilt Platform provides a lightweight, sturdy two-axis mount for cameras commonly used with Arduino and Raspberry Pi. Two digital servos deliver smooth pan and tilt movement, while an included I²C controller board makes integration with your favourite microcontrolle...

SKU: AF-3928

The Adafruit CRICKIT for micro:bit is a robotics and electronics driver board designed for the BBC micro:bit. Plug your micro:bit into the 40-pin edge connector and start controlling motors, servos, solenoids, NeoPixels, capacitive touch sensors, and a speaker — all managed over I2C via the Adafr...

SKU: WS-24004

Raspberry Pi Pico Entry-Level Sensor Kit Including 15 Common Modules Such As LED, Button, Buzzer, Etc.Out Of The Box As A Whole Kit, Or Can Be Separated To Use Independently Comes With Online Development Resources And Manual Features At A Glance Standard Raspberry Pi Pico header, supports Raspber...

SKU: AF-2946

The Adafruit IS31FL3731 breakout is a charlieplexed PWM LED matrix driver that controls a 16×9 grid of individually dimmable LEDs over I2C. Each of the 144 LEDs can be set to any brightness level with 8-bit (256-level) PWM — no complex wiring or constant signal sending required. The IS31FL3731 o...

SKU: DF-DFR0592

The DC Motor Driver HAT is a Raspberry Pi add-on board that drives up to two DC motors via I2C. Built around the TB6612FNG motor driver chip with 1.2 A continuous current per channel (2 A peak), it supports both standard DC motors and motors with encoders through the on-board encoder interface. ...

SKU: WS-19767

Servo Driver Module For Pico Ideal For Controlling Robotic Arm Or Hexapod Walker Features At A Glance Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards Up to 16-Channel servo/PWM outputs, 16-bit resolution for each channel Integrates 5V regulator, up to 3A output ...

SKU: AF-4280

The Adafruit DC & Stepper Motor Bonnet drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET mo...

SKU: AF-5690

The Adafruit ATtiny1616 Breakout with seesaw is a versatile development board that combines an ATtiny1616 microcontroller with the Adafruit seesaw I2C framework and STEMMA QT connectivity. It works as both a standalone dev board and an I2C peripheral that adds GPIO, ADC, PWM, and NeoPixel support...