All Products

SKU: AF-757

This bi-directional logic level converter from Adafruit uses 4× BSS138 FETs with 10K pull-up resistors to safely shift signals between different voltage levels. Unlike many level shifters, this design is fully compatible with I2C's open-drain pull-up signalling, following NXP's recommended applic...

SKU: SF-BOB-12009

The SparkFun Bi-Directional Logic Level Converter safely translates signals between different voltage levels — stepping 5V down to 3.3V and 3.3V up to 5V on the same channel. It also works with 2.8V and 1.8V devices, making it a versatile bridge between mixed-voltage systems. Each board provides...

SKU: SF-BOB-15439

The SparkFun PCA9306 Level Translator Breakout provides dual bidirectional voltage-level translation for I2C and SMBus lines. It lets you safely connect devices operating at different logic levels — for example, a 3.3V sensor to a 5V microcontroller — without a direction pin. Simply apply your re...

SKU: AF-1875

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.Although one can use resistors to make a divider, for high speed tr...

SKU: LB-LR0185

Logic Level Converter Bi-Directional IIC 4 Way Level Conversion Module Description:If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3....

SKU: DF-DFR0913

This DFRobot 4-channel optocoupler-isolated level converter translates 12V signals down to 3.3V, making it easy to interface industrial sensors and PLC outputs with Arduino, Raspberry Pi, and other 3.3V microcontrollers. Each channel features photoelectric isolation for reliable signal separation...

SKU: DF-DFR0914

This DFRobot 4-channel optocoupler-isolated level converter translates 12V signals down to 5V, making it easy to interface industrial sensors and PLC outputs with Arduino and other 5V microcontrollers. Each channel features photoelectric isolation for reliable signal separation between high and l...

SKU: LB-LS0221

The CJMCU-226 INA226 is a powerful voltage, current, and power monitoring module designed for high precision in both high-side and low-side sensing applications. With its bi-directional current sensing capability and wide operating range, this module is perfect for a variety of applications, incl...

SKU: AF-1787

A quad level-shifting buffer IC that excels at converting 3V logic signals up to 5V. Power the 74AHCT125 with 5V and it will cleanly detect 3.3V logic inputs — particularly useful when connecting devices like Teensy 3.x to NeoPixels or other 5V peripherals. To use, apply 5V to VCC, connect GND, ...

SKU: SF-PRT-14765

The SparkFun Single Supply Logic Level Converter is logic level and power supply translator in one small package. This little board breaks out the Texas Instruments TXB0104 4-bit bi-directional voltage-level translator with automatic direction sensing. With this logic level converter you wil...

SKU: AF-4903

The Adafruit ISO1540 Bidirectional I2C Isolator provides full electrical isolation between two sides of an I2C bus, using the TI ISO1540 chip with 2500 V-RMS isolation. It's ideal for separating earth-grounded circuits, reducing noise, or protecting sensitive equipment in power monitoring setups....

SKU: SF-SEN-29259 · MPN: SEN-29259

Built around the Allegro ACS37800, this Qwiic power meter lets your project monitor voltage and current at the same time over I2C. It is designed for higher-demand loads such as 3D printers, UAVs and solar panels, with voltage monitoring up to 60VDC and current sensing up to 30A.The ACS37800 uses...

SKU: AF-5649

The Adafruit QT 3V to 5V Level Booster Breakout lets you connect 3.3 V STEMMA QT / Qwiic devices to sensors and peripherals that require 5 V power or logic. Most modern microcontrollers (ESP32, RP2040, SAMD, micro:bit) run at 3.3 V, but some sensors and modules still need 5 V — this board bridges...

SKU: SF-PRT-28203 · MPN: PRT-28203

  The SparkFun Qwiic 5V Boost simplifies interfacing 5V I2C devices with the 3.3V Qwiic ecosystem. It takes the 3.3V I2C signals and power from its Qwiic connectors and boosts them to 5V, available on the PTH pins. This is perfect for powering peripherals like RGB LEDs or DC fans commonl...

SKU: AF-5663

Need to use multiple I2C devices that share the same address? The PCA9546 4-Channel I2C Multiplexer lets you connect up to four same-address I2C devices to a single microcontroller by acting as a gatekeeper — write a single byte to select the active channel and all subsequent I2C traffic is route...

SKU: AF-5664

Need to use multiple I2C devices that share the same address? The PCA9546 4-Channel STEMMA QT / Qwiic I2C Multiplexer lets you connect up to four same-address I2C devices with completely solderless wiring. Five JST SH connectors (1 input + 4 outputs) make it plug-and-play with any STEMMA QT or Qw...

SKU: AF-735

An 8-bit logic level shifter in a breadboard-friendly DIP package. The 74LVC245 converts between 3.3V and 5V logic levels, making it easy to interface modern 3.3V sensors and peripherals with 5V microcontrollers like Arduino. Even when powered at 1.8V, the chip safely accepts up to 5V signals on...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: DF-DFR1229 · MPN: DFR1229

This GP8600 module is a high-precision digital-to-analogue converter for connecting logic-level microcontrollers to industrial-style analogue control inputs. It accepts I2C or PWM signals and converts them for applications such as 0-5V, 0-10V and 4-20mA control.It is designed for automation and c...

SKU: LB-LR0051

A 4-channel relay module with opto-isolated inputs for safe, reliable switching of high-power loads. Each relay is rated for up to 10A at 250VAC or 30VDC, making it suitable for controlling lights, motors, heaters, and other mains-powered devices from a microcontroller. The opto-isolators protec...