All Products
Showing 1-20 of 60 products
MyoWare 2 Muscle Sensor Wireless Kit
·
Build and test wireless muscle-sensing projects with this Arduino-compatible electromyography (EMG) kit from the MyoWare 2 ecosystem. It centres on the MyoWare 2 Muscle Sensor, which measures muscle activity from the electric potential at the skin, commonly called surface electromyography or sEMG...
MyoWare 2.0 Muscle Sensor
·
Control a project with muscle activity instead of buttons, levers or joysticks. The MyoWare® 2.0 Muscle Sensor is an all-in-one surface electromyography (sEMG) sensor that detects the electrical signals generated when a muscle flexes, then outputs an analogue signal representing the strength of t...
MyoWare Muscle Sensor
The MyoWare Muscle Sensor is an all-in-one electromyography (EMG) sensor that measures the filtered and rectified electrical activity of a muscle. It outputs 0 V to Vs (supply voltage) depending on the level of activity in the selected muscle, making it straightforward to read with any analogue i...
MyoWare 2 Muscle Sensor Development Kit
·
This all-in-one electromyography (EMG) kit gives you the MyoWare 2 boards needed to experiment with different muscle-sensing setups. Depending on how you configure it, you can visualise muscle activity with the MyoWare 2 LED Shield or read an analogue output with an Arduino-compatible microcontro...
MyoWare 2 Muscle Sensor Basic Kit
·
This all-in-one MyoWare 2 electromyography (EMG) kit gives you the essentials for measuring and visualising muscle activity. It is Arduino-compatible, but the included setup is designed to follow the standalone example from the MyoWare 2 Muscle Sensor Guide, so you can use it without a microcontr...
MyoWare 2.0 LED Shield
·
This shield gives your MyoWare 2.0 Muscle Sensor an easy visual output, using a blue 10-segment bar graph to show the magnitude of a target muscle’s signal. As muscle activation increases, the LEDs climb further up the board.It snaps onto the top side of the MyoWare 2.0 Muscle Sensor using the on...
MyoWare 2.0 Cable Shield
The MyoWare® 2.0 Muscle Sensor is designed to be wearable, allowing you to attach biomedical sensor pads directly to the board itself. However, there still may be cases where you want to mount the sensor pads away from the board; this is where the MyoWare 2.0 Cable Shield comes in. The shield inc...
MyoWare 2.0 Arduino Shield
The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would need to do is stack it on your Arduino and connect the sensors to read up to si...
MyoWare 2.0 Wireless Shield
·
The MyoWare® 2.0 Wireless Shield is designed to take in readings from the MyoWare 2.0 Muscle Sensor and wirelessly transmit sensor data with the ESP32-WROOM! This shield also includes a built-in LiPo battery to remotely power the muscle sensor and the ESP32 module. The Wireless Shield is equipped...
MyoWare 2.0 Link Shield
The MyoWare 2.0 Link Shield connects a MyoWare 2.0 Muscle Sensor to your Arduino microcontroller via a 3.5mm TRS cable. Simply snap the Link Shield onto your Muscle Sensor using the built-in snap connectors, connect a TRS-to-TRS cable, and link it to the MyoWare 2.0 Arduino Shield on your develop...
MyoWare 2.0 Power Shield
·
The MyoWare® 2.0 Power Shield is designed to easily power the MyoWare 2.0 Muscle Sensor for remote applications. The MyoWare Power Shield is equipped with snap connectors on the board so you can easily stack it to the top side of the MyoWare Muscle Sensor. Flip the switch to the ON position to gi...
MyoWare Electrodes (10-pack)
A pack of 10 disposable, pre-gelled foam electrodes designed for use with MyoWare Muscle Sensors. Each electrode snaps directly onto the sensor for quick and clean electromyography (EMG) measurements — no additional gel or preparation required. The integrated adhesive foam backing adheres secure...
MyoWare 2.0 Reference Cable
The MyoWare 2.0 Reference Cable extends the reference pin on the MyoWare 2.0 Muscle Sensor, allowing you to place the reference electrode on a separate part of the body. This is useful when the sensor's built-in reference pin cannot reach a suitable location, such as a bony portion of the elbow o...
![Muscle Sensor Surface EMG Electrodes - H124SG Covidien [Pack of 6]](/rails/active_storage/representations/redirect/BAh7BkkiC19yYWlscwY6BkVUewdJIglkYXRhBjsAVGkCr4ZJIghwdXIGOwBUSSIMYmxvYl9pZAY7AEY=--0216f6846afa24186e1573fc5b39450260cf8bad/BAh7BkkiC19yYWlscwY6BkVUewdJIglkYXRhBjsAVHsHOgtmb3JtYXRJIghqcGcGOwBUOhJyZXNpemVfdG9fZml0WwdpApABaQKQAUkiCHB1cgY7AFRJIg52YXJpYXRpb24GOwBG--4cc5678865497cdbcf7b02aee5242eda5f847322/image_6959a3e0-09ab-4da1-8a97-3ab126f211f2.jpg)
Muscle Sensor Surface EMG Electrodes - H124SG Covidien [Pack of 6]
·
Have your next project be controlled by your muscles with this pack of Muscle Sensor Surface EMG Electrodes! Pair the electrodes with the MyoWare Muscle Sensor and a microcontroller (ie. Arduino, or anything else with analog input reading ability) to create a DIY low-cost v...
MyoWare 2.0 Reference Cable - 10 pack
This is a 10 pack of the MyoWare® Reference 2.0 Cables. The MyoWare 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the pin into its housing and place a biomedical sensor pad into the electrode snap. When ready, stick th...
Gravity: Analog EMG Sensor by OYMotion
The Gravity Analog EMG Sensor by OYMotion detects surface electromyography (sEMG) signals to measure muscle and neural activity. The sensor amplifies the tiny sEMG signal (±1.5 mV) by 1000× and filters noise through differential input and analogue filtering, outputting a clean 0–3.0V analogue sig...
Gravity GP8600 1-Channel I2C/PWM 16-bit DAC Module
·
This GP8600 module is a high-precision digital-to-analogue converter for connecting logic-level microcontrollers to industrial-style analogue control inputs. It accepts I2C or PWM signals and converts them for applications such as 0-5V, 0-10V and 4-20mA control.It is designed for automation and c...
XRP Build-Your-Own Robotics Kit Parts - 30 Pack
·
The Experiential Robotics Platform (XRP) is a hands-on robotics platform designed for learning, prototyping and classroom projects. This build-your-own 30 pack supplies the hardware pillar of the XRP ecosystem, helping students build and program robots from beginner tasks through to more advanced...
Adafruit ICM-20649 Wide Range ±30g ±4000dps 6-DoF IMU
·
The Adafruit ICM-20649 breakout features a wide-range 6-DoF IMU capable of measuring up to ±30g acceleration and ±4000°/s gyroscope rotation — roughly double the range of standard IMUs. When typical ±16g accelerometers and ±2000°/s gyros aren't enough, this sensor delivers the extended measuremen...
Long Flex sensor
·
This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.These sensors are easy to use, they are basically resistors that change value based on how much they're flexed. If they're unflexed, the resistance...
