All Products

SKU: AF-3406

The Feather nRF52 Bluefruit LE is an all-in-one Bluetooth Low Energy development board built around the Nordic nRF52832. Unlike earlier Bluefruit Feathers that used a separate helper chip, the nRF52832 runs your application code and handles BLE directly — resulting in lower power consumption, low...

SKU: AF-3574

The Feather nRF52 Pro is an advanced Bluetooth Low Energy development board built around the Nordic nRF52832, designed specifically for use with the Apache Mynewt RTOS. It features a fully open-source BLE 5.0 stack, a serial bootloader for command-line firmware flashing, and an on-board SWD debug...

SKU: AF-3242

The Feather 32u4 Bluefruit LE with Stacking Headers combines an ATmega32u4 microcontroller with a Bluetooth Low Energy module, USB connectivity, and LiPo battery charging — with stacking headers pre-soldered so you can plug into a breadboard and stack FeatherWings on top. The Bluefruit module is...

SKU: AF-3379

The Feather 32u4 Bluefruit LE with Headers combines an ATmega32u4 microcontroller with a Bluetooth Low Energy module, USB connectivity, and LiPo battery charging — with standard headers pre-soldered so you can plug straight into a breadboard. The Bluefruit module is built on the Nordic nRF51822 ...

SKU: AF-2829

The Feather 32u4 Bluefruit LE combines an ATmega32u4 microcontroller with a Bluetooth Low Energy module, USB connectivity, and LiPo battery charging in one compact board. BLE is supported by all modern smartphones and tablets (iOS, Android, Mac OS X, Windows 8+), making it ideal for portable proj...

SKU: AF-3128

The Adafruit 0.54" Quad Alphanumeric FeatherWing Display in blue adds a bright, 4-character 14-segment LED display to any Feather board. Each character can display letters, numbers, and symbols, making it ideal for clocks, status indicators, sensor readouts, and more. Driven by the HT16K33 I2C m...

SKU: AF-4062

The Feather nRF52840 Express upgrades the nRF52 Bluefruit with the Nordic nRF52840 — featuring 1 MB flash, 256 KB SRAM, native USB, and Bluetooth Low Energy in a single chip. Native USB means no separate serial converter is needed; the chip handles CDC serial, and can also act as a HID keyboard, ...

SKU: AF-2995

The Feather M0 Bluefruit LE combines an ATSAMD21G18 ARM Cortex M0 processor with a Bluetooth Low Energy module, native USB, and LiPo battery charging. With the power of a 48 MHz ARM core and 256KB of flash, it provides significantly more processing headroom than the 32u4-based Bluefruit while mai...

SKU: AF-3077

The Feather 32u4 RFM69HCW Packet Radio (433 MHz) combines an ATmega32u4 microcontroller with an SX1231-based packet radio transceiver operating at 433 MHz, USB connectivity, and LiPo battery charging. It offers longer range than 2.4 GHz protocols (Bluetooth, Wi-Fi, ZigBee) with more flexibility t...

SKU: AF-3106

Add a bright, easy-to-read numeric display to your Feather project with the Adafruit 4-Digit 7-Segment FeatherWing in blue. This combo pack includes the HT16K33-based FeatherWing backpack and a matching 0.56" tall blue 7-segment display with decimal points and a centre colon for clock displays. ...

SKU: AF-3078

The Feather 32u4 RFM95 LoRa Radio (868/915 MHz) combines an ATmega32u4 microcontroller with an SX1276 LoRa radio transceiver, USB connectivity, and LiPo battery charging. LoRa modulation provides dramatically longer range than standard packet radio — over 2 km line-of-sight with default settings ...

SKU: AF-2633

The Adafruit Bluefruit LE SPI Friend adds Bluetooth Low Energy connectivity to any microcontroller with just 4–5 GPIO pins. Using SPI instead of UART means no baud rate configuration or flow control to worry about — connect via MISO, MOSI, SCK, CS, and an interrupt pin, and you're ready to go. T...

SKU: AF-2479

The Adafruit Bluefruit LE UART Friend adds Bluetooth Low Energy connectivity to any microcontroller or computer with a hardware or software serial port. With hardware flow control built in, you won't lose data during transmission. Connect via UART TX/RX pins, or use a standard FTDI cable for debu...

SKU: AF-2746

The Adafruit Bluefruit LE Shield adds Bluetooth Low Energy connectivity to your Arduino in a plug-in shield form factor. Solder the included headers, stack it on your Arduino, and start communicating wirelessly with iOS and Android devices — no special iOS certification required. The shield conn...

SKU: AF-3076

The Feather 32u4 RFM69HCW Packet Radio (868/915 MHz) combines an ATmega32u4 microcontroller with an SX1231-based packet radio transceiver, USB connectivity, and LiPo battery charging. It offers longer range than 2.4 GHz protocols (Bluetooth, Wi-Fi, ZigBee) with more flexibility than BLE, making i...

SKU: AF-4516

The Feather nRF52840 Sense takes the popular Feather nRF52840 Express and adds a suite of on-board environmental and motion sensors. It features Bluetooth Low Energy, native USB, CircuitPython and Arduino support, plus sensors for acceleration, gyroscope, magnetometer, proximity, light, colour, g...

SKU: AF-3079

The Feather 32u4 RFM96 LoRa Radio (433 MHz) combines an ATmega32u4 microcontroller with an SX1276 LoRa radio transceiver operating at 433 MHz, USB connectivity, and LiPo battery charging. LoRa modulation provides dramatically longer range than standard packet radio — over 2 km line-of-sight with ...

SKU: AF-3178

The Feather M0 RFM95 LoRa Radio (900 MHz) combines the ATSAMD21G18 ARM Cortex M0+ processor with an SX1276-based LoRa radio transceiver for long-range wireless communication at 868 or 915 MHz. The exact frequency is software-configurable, allowing you to tune dynamically for your region's ISM ban...

SKU: AF-2771

The Feather 32u4 Basic Proto is the no-frills member of the Feather 32u4 family, with a built-in prototyping area where you can solder on extra components like buttons, sensors, or connectors without needing a separate breadboard. Built around the ATmega32u4 running at 8 MHz with 3.3V logic and ...

SKU: AF-2795

The Feather 32u4 Adalogger is an all-in-one datalogger built around the ATmega32u4, with a built-in MicroSD card holder, USB connectivity, and LiPo battery charging. Ready to log data straight out of the box — just add a MicroSD card and start recording. The ATmega32u4 runs at 8 MHz with 3.3V lo...