All Products

SKU: DF-DFR0592

The DC Motor Driver HAT is a Raspberry Pi add-on board that drives up to two DC motors via I2C. Built around the TB6612FNG motor driver chip with 1.2 A continuous current per channel (2 A peak), it supports both standard DC motors and motors with encoders through the on-board encoder interface. ...

SKU: SF-ROB-09571

The SparkFun Serial Controlled Motor Driver allows you to control up to two DC motors using a serial command interface. The serial interface is easy to use and it lets the user select an individual motor, the direction, and the desired speed constant (up to 10 different speed from stop to full sp...

SKU: MB-12040

This encoder motor is capable of driving two DC motors or one encoder motor. It has 16 pins, allowing you to connect with MegaPi by simply plugging in. The motor driver IC on the board is TB6612, which is a high efficiency MOSFET driver with low heat dissipation. Overcurrent protection included t...

SKU: SF-ROB-14451

The SparkFun TB6612FNG Motor Driver breakout can independently control up to two DC motors at a constant current of 1.2 A (3.2 A peak). Each motor channel supports four modes — clockwise, counter-clockwise, short-brake, and stop — controlled via two input signals and a PWM speed input. All pins ...

SKU: AF-3297

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...

SKU: SF-ROB-14450

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake and stop. The two motor outputs (A and B) can be separately controlled, and t...

SKU: PL-2515

The Pololu Dual G2 High-Power Motor Driver 18v18 Shield uses pairs of discrete MOSFET H-bridges to drive two large brushed DC motors. It has an Arduino shield form factor for direct plug-in use, and also breaks out all motor driver pins along the left side for standalone operation without an Ardu...

SKU: DF-DFR0601

This is a dual channel DC motor driver with an extremely small size of of 1.97”×1.97”×0.49”. The module comes with two motor channels that can drive two motors simultaneously, and each channel employs an indicator to show the rotation direction of the motor: blue is forward rotation, red is rever...

SKU: DF-DRI0058 · MPN: DRI0058

This compact DFRobot driver board is made for precise control of brushless DC motors using Field-Oriented Control (FOC). At just 26 x 21.5mm, it is well suited to tight builds where smooth motion, low noise and responsive control matter.SimpleFOCmini supports closed-loop control of motor position...

SKU: PL-4733

The MP6550 from Monolithic Power Systems (MPS) is an H-bridge motor driver IC that can be used for bidirectional control of one brushed DC motor at 1.8 V to 22 V. It can supply up to about 1.7 A continuously and features configurable current sensing and current limiting. Since this board is a car...

SKU: AF-6121 · MPN: ADA6121

The Adafruit TMC2209 Stepper Motor Driver Breakout Board makes controlling stepper motors easy and virtually silent. Using Trinamic's "Stealth Chopper" technology, this driver delivers smooth, quiet microstepping with just two control pins — no timers, PWM, or real-time microcontroller required. ...

SKU: DF-DRI0024

The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics. Out of the box, the SyRen 10 can supply a single DC brushed motor with up to 10...

SKU: AF-807

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....

SKU: AF-3190

The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: AF-2348

The Adafruit DC & Stepper Motor HAT drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET motor...

SKU: SF-ROB-15451

The SparkFun Qwiic Motor Driver takes all the great features of the Serial Controlled Motor Driver (SCMD) and miniaturizes them, adding Qwiic ports for plug and play functionality. Boasting the same 4245 PSOC and 2-channel motor ports as the SCMD, the SparkFun Qwiic Motor Driver is designed to co...

SKU: EC-MCS02930M

This Adruino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motor or two 4-wire stepper and two 5v servo. It drive the DC motor and stepper with the L293D,and it drive the servo with arduino pin9 and pin10. Features Be able to drive 4 DC motor and...

SKU: SB-21468

Pico Driver Motor HAT is a DC motor control module that is powered by one H-bridge IC L293D with the motor input supply range 6 V-12 V. It is designed to connect 2 DC motors simultaneously or 1 stepper motor that would help the user to make projects in a compact size with high efficiency. You ca...

SKU: AF-4280

The Adafruit DC & Stepper Motor Bonnet drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET mo...