All Products
Collections
Showing 81-100 of 100 products
W5200 Ethernet Shield
The W5200 Ethernet Shield adds wired internet connectivity to your Arduino. Simply stack it onto your board, connect an RJ45 cable, and start communicating over the network. The W5200 controller provides a 32 KB internal buffer — double that of the W5100 — and supports up to eight simultaneous TC...
SparkFun IoT RedBoard - ESP32 MicroPython Development Board - SparkFun Electronics
·
The SparkFun IoT RedBoard combines the powerful ESP32-D0WDQ6 microcontroller with MicroPython pre-installed, letting you start coding IoT projects right out of the box. No need for complex toolchains – just connect via USB and start writing Python code. With built-in WiFi and Bluetooth, plus a f...
Arduino Uno Rev 3
This is the new Arduino Uno Rev 3. In addition to all the features of the previous board, the arduino Uno Rev 3 now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linu...
Arduino Uno R3
Note: This product is manufactured in Italy by affiliates of Arduino Srl, and the product packaging suggests downloading the Arduino IDE from arduino.org. However, we use and recommend using the normal Arduino IDE from arduino.cc, which is the IDE we ensure our Arduino libraries work with. Ard...
SparkFun RedBoard Artemis
The SparkFun RedBoard Artemis brings the powerful Artemis module into a familiar Arduino Uno footprint. Built around the Ambiq Apollo3 processor, it runs at 48 MHz (with 96 MHz turbo mode), includes BLE 5.0, and draws less than 1 mA in sleep — making it capable of running TensorFlow Lite models f...
Octopus Analog Photocell Brick OBPhotocell
The Octopus Analog Photocell Brick is a light-dependent resistor (LDR) module from the ElecFreaks Octopus Electronic Bricks series. It uses a cadmium-sulfide (CdS) photocell that changes resistance based on ambient light levels — the brighter the light, the lower the resistance. With its 3-pin co...
MyoWare 2.0 Muscle Sensor
·
Control a project with muscle activity instead of buttons, levers or joysticks. The MyoWare® 2.0 Muscle Sensor is an all-in-one surface electromyography (sEMG) sensor that detects the electrical signals generated when a muscle flexes, then outputs an analogue signal representing the strength of t...
2x2A DC Motor Shield For Arduino
The DFRobot 2×2A DC Motor Shield uses the L298P dual full-bridge driver chip to control two DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 5 and 6 for speed control and digital pins 4 and 7 for enable/disable. The shield can be pow...
Motor party add-on pack for Arduino
Make your own Arduino motor party with a motor shield and a fine assortment of motors! New! we've upgraded the shield to our new version 2, with more powerful drivers, and uses fewer pins to boot! Included in this add-on pack is: Adafruit Motor Shield v2 for Arduino 6 Volt DC hobby motor Smal...
![Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit [v2.3]](/rails/active_storage/representations/redirect/BAh7BkkiC19yYWlscwY6BkVUewdJIglkYXRhBjsAVGkCxwVJIghwdXIGOwBUSSIMYmxvYl9pZAY7AEY=--be53511e4bffcc386d14cc91e4d5fa7bc52d1658/BAh7BkkiC19yYWlscwY6BkVUewdJIglkYXRhBjsAVHsHOgtmb3JtYXRJIghqcGcGOwBUOhJyZXNpemVfdG9fZml0WwdpApABaQKQAUkiCHB1cgY7AFRJIg52YXJpYXRpb24GOwBG--4cc5678865497cdbcf7b02aee5242eda5f847322/image_cffee67c-857a-46f6-8d7e-71857a2f29bb.jpg)
Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit [v2.3]
The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...
Gravity: Analog Spear Tip pH Sensor / Meter Kit (for Soil and Food Applications)
The Gravity Spear Tip pH Sensor Kit is designed for measuring the pH of semi-solid materials such as wet soil, fruit, meat, and vegetables. The stainless steel spear tip protects the glass electrode and allows the probe to be pushed directly into soft materials — something standard pH probes cann...
Octopus Button Switch Brick OBButton
The Octopus Button Switch Brick is a simple, plug-and-play pushbutton module from the ElecFreaks Octopus Electronic Bricks series. It features a large button with a transparent cap — you can insert a custom label underneath for easy identification in your projects. Designed for breadboard-free c...
Industrial 8-Channel Digital Input & Output Module (Modbus RTU)
An RS485-controlled industrial I/O module with 8 isolated digital inputs and 8 open-drain digital outputs, communicating via the Modbus RTU protocol. Multiple protection layers — power isolation, magnetic isolation, TVS diode, and resettable fuse — ensure stable and reliable operation in demandin...
Qwiic Alphanumeric Display - Red
·
Add letters, numbers and symbols to your project with red fourteen-segment digits that are much more flexible than a basic seven-segment display. This Qwiic display connects over I2C, so you can plug it in without soldering, without working out SDA and SCL by hand, and without adding separate vol...
Ethernet Shield for Arduino - W5200
An Arduino-compatible Ethernet shield based on the Wiznet W5200 chip, providing a simple way to connect your Arduino to a network. It plugs directly onto an Arduino Uno or Mega 2560 and supports stacking additional shields on top. An aluminium alloy heatsink is fitted to the W5200 chip for therma...
Motoron M3S256 Triple Motor Controller Shield for Arduino (Connectors Soldered)
The Motoron M3S256 Triple Motor Controller Shield for Arduino makes it easy to control DC motors from an Arduino or Arduino-compatible board through an I²C interface. Each module can independently control up to three motors, and multiple shields can be stacked on top of the same Arduino for proje...
Adafruit NeoPixel Shield for Arduino - 40 RGB LED Pixel Matrix
Put on your sunglasses before plugging in this shield — 40 eye-blistering RGB LEDs adorn the NeoPixel Shield for a blast of configurable colour. Arranged in a 5×8 matrix, each pixel is individually addressable using just one pin (Digital #6 by default, changeable by cutting a trace). This is the...
Arduino Nano
The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x).It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard ...
Adafruit NeoPixel Shield - 40 RGBW - Natural White - ~4500K
Put on your sunglasses before plugging in this shield — 40 eye-blistering RGBW LEDs adorn the NeoPixel Shield for a blast of configurable colour and white. Arranged in a 5×8 matrix, each pixel is individually addressable using just one pin (Digital #6 by default, changeable by cutting a trace). ...
Gravity: URM09 Analog Ultrasonic Sensor
The DFRobot URM09 is an analog output ultrasonic distance sensor optimised for fast ranging and obstacle avoidance. With a maximum measurement rate of 30Hz, built-in temperature compensation, and a range of 2–500cm, it's a capable and easy-to-use sensor for robotics, automation, and detection pro...
