All Products

SKU: SF-DEV-15794

The SparkFun Qwiic SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a Qwiic connector to your Raspberry Pi. The SHIM design allows you to plug directly to the Pi's I2C bus with no soldering required and the thin PCB design allows for it to be sandwiched on your Pi GPIO...

SKU: SF-COM-15093

Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino or another low powered microcontroller? The SparkFun Qwiic Single Relay provides you with the easiest to use relay yet. The Single Relay board can handle up to 5.5A at 2...

SKU: SF-DEV-20690

The SparkFun Qwiic Speaker Amp includes the Texas Instruments TPA2016D2 stereo, filter-free class-D audio power amplifier. What distinguishes this audio amplifier from others is that it features volume control (i.e. gain), Dynamic Range Compression (DRC), Automatic Gain Control (AGC), enable/disa...

SKU: SF-SEN-16294

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: SF-SEN-16295

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: SF-SEN-18642

The SparkFun Qwiic ToF Imager is a state of the art, 64 pixel Time-of-Flight (ToF) 4 meter ranging sensor built around the VL53L5CX from ST. This chip integrates a SPAD array, physical infrared filters, and diffractive optical elements (DOE) to achieve the best ranging performance in various ambi...

SKU: SF-DEV-15083

The SparkFun Qwiic Twist is a digital RGB rotary encoder breakout with built-in I²C interface. It handles all interrupt management, switch debouncing, and LED PWM internally, presenting encoder position, button state, and RGB colour control over a simple I²C connection via Qwiic connectors. The ...

SKU: SF-WRL-18567

Ultra. Low. Power. Arguably the best three words in the IoT world. SparkFun has teamed up with ARM and Dialog to provide you with this Qwiic WiFi Shield based around the DA16200 module. The DA16200 is a fully integrated WiFi module with a 40MHz crystal oscillator, 32.768KHz RTC clock, RF Lumped R...

SKU: SF-BOB-12708

This is the SparkFun Real Time Clock (RTC) Module, this little breakout that uses the DS1307 to keep track of the current year, month, day as well as the current time. The module comes fully assembled and includes a small CR1225 Lithium coin cell battery that will run the RTC for a minimum of 9 y...

SKU: SF-BOB-14558

Get with the times, already! This SparkFun Real Time Clock (RTC) Module is a Qwiic-enabled breakout board for the RV-1805 chipset. The RTC is ultra-low power (running at only about 22nA in its lowest power setting) so it can use a supercapacitor for backup power instead of a normal battery. ...

SKU: SF-BOB-16281

The SparkFun RV-8803 Real Time Clock Module is a Qwiic-enabled breakout for the RV-8803 RTC, featuring a factory-calibrated temperature-compensated crystal for extremely precise timekeeping. It tracks hundredths of seconds, seconds, minutes, hours, date, month, year, and weekday, with multiple al...

SKU: SF-DEV-15444

The SparkFun RedBoard Artemis brings the powerful Artemis module into a familiar Arduino Uno footprint. Built around the Ambiq Apollo3 processor, it runs at 48 MHz (with 96 MHz turbo mode), includes BLE 5.0, and draws less than 1 mA in sleep — making it capable of running TensorFlow Lite models f...

SKU: SF-DEV-15442

The RedBoard Artemis ATP is affectionately called 'All the Pins!' at SparkFun. The Artemis module has 48 GPIO and this board breaks out absolutely every one of them in a familiar Mega like form factor. What's with the silkscreen labels? They're all over the place. We decided to label the pins as ...

SKU: SF-DEV-15443

The SparkFun RedBoard Artemis Nano packs the powerful Artemis module into a minimal, 0.8 mm thick PCB with USB-C programming, on-board LiPo battery charging, and a Qwiic connector. It's a compact, modern replacement for the Arduino Uno or Nano with significantly more processing power, memory, and...

SKU: SF-DEV-13975

At SparkFun we use many Arduinos and we’re always looking for the simplest, most stable one. Each board is a bit different and no one board has everything we want, so we decided to make our own version that combines all our favorite features. The SparkFun RedBoard combines the simplicity of the U...

SKU: SF-DEV-15123

The SparkFun RedBoard Qwiic is an Arduino-compatible development board in the UNO R3 form factor with a built-in Qwiic connector for solderless I2C hookup. It programs over USB Micro-B using the Arduino IDE — select "Arduino UNO" from the board menu and you're ready to go. Key improvements over ...

SKU: SF-DEV-14812

If you’re ready to step up your Arduino game from older 8-bit/16MHz microcontrollers, the SparkFun RedBoard Turbo is a formidable alternative. At its heart, the RedBoard Turbo uses the ATSAMD21G18, which is an ARM Cortex M0+, 32-bit microcontroller that can run at up to 48MHz. With an impressive ...

SKU: SF-ROB-12567

This buzzer is an add-on for your RedBot that gives your robot the ability to make awesome beep-boop noises or alerts when something interesting (or terrible) happens. The buzzer works by making use of two I/O pins on a controller board to create different noises based on the different frequ...

SKU: SF-SEN-12589

The SparkFun RedBot Accelerometer is an add-on sensor that provides bump and motion detection for the RedBot platform. It measures acceleration forces on the X, Y, and Z axes using the MMA8452Q triple-axis accelerometer, giving your robot awareness of its movements and orientation. The sensor co...

SKU: SF-SEN-11769

The Line Follower sensor is an add-on for your RedBot that gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measuring the amount of reflected infrared light, it can detect transitions from light t...