All Products

SKU: EC-CIL13002M2

Elecrow ThinkNode-M2 is a high-performance LoRa signal transceiver. It uses the ESP32-S3 module as the main processor and supports Bluetooth. Users can easily configure and monitor the device through their mobile phones. M2 is pre-installed with Meshtastic firmware and equipped with an SX1262 wi...

SKU: EC-ILM13205D2-915

The Elecrow ThinkNode M5 is a high-performance LoRa communication device powered by the ESP32-S3 processor. Pre-installed with Meshtastic firmware and featuring the SX1262 wireless chip, it efficiently sends and receives LoRa signals for off-grid mesh networking. With its compact, integrated des...

SKU: EC-LMM14606D2

The ThinkNode M6 Outdoor Solar Power is a high-performance LoRa IoT device designed for harsh outdoor environments and industrial scenarios.It features the nRFLR1262 LoRa transceiver module and the nRF52840 core processor, supporting Bluetooth and LoRa dual-mode connectivity to ensure stable sign...

SKU: AF-1891

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value). We particularly like th...

SKU: AF-5729

Look, over there at that thing! Take it apart! You can now attack just about every kind of box or enclosure that needs undoing with this 9-piece screwdriver set. This kit is of fine quality and excels at disassembling games, phones, cameras, and other small portable electronic goodies.What drew u...

SKU: SF-COM-15350

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind you might find in one of those "talking greeting cards".

SKU: SF-COM-21311

A compact, thin speaker ideal for projects where space is tight. At just 28 mm in diameter and approximately 4 mm thick, it fits into enclosures and wearables where standard speakers won't. The pre-wired 180 mm cable terminates in a 2-pin JST connector for easy hookup. Key Features 28mm Diamet...

SKU: AF-3763

We're keepin' it wheel with this one! Plastic gear-box motors (also known as 'TT' motors) are an easy and low cost way to get your projects moving. But we've noticed that there are not a lot of nice TT motor wheels to go along with them. This Thin White Wheel has solid...

SKU: SF-TOL-09317

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but soldering flat on a table works just fine. Then again, the desk is starting to loo...

SKU: PK-SN-392

The useful helping hands is ideal for soldering work and detail jobs.Widely used in the fields of industrial electronics, laboratories,  jewelry and more.Holding objects firmly for precision projects. Quality helping hands with heavy iron base. Adjustalbe clips hold work at any angle. Co...

SKU: SF-TOL-18472 · MPN: TOL-18472

These threaded inserts are a handy way to add strong, reusable fixing points to a jig, fixture or machine wasteboard. Place a few exactly where you need hold-down points, or install them in a grid pattern to turn a wasteboard into a threaded table.Installation is straightforward: create a 9mm pil...

SKU: SF-ROB-20441

A 3-phase DC brushless DC motor has the unique capability of being both a high efficiency, high torque, very smooth motor, as well as the starting point for haptic feedback when combined with the appropriate sensor and motor control. For an excellent demonstration of what's possible with 3-phase ...

SKU: EC-RPA00273R

This handy Three Wire Display Stand is made for Raspberry Pi, but also can adapt to other tablet PC, such as iPad. It is great for general electronics & TFT holding. You can adjust the angle as you like. Features Fully adjustable Vinyl Coated Steel Wire that will not scratch furniture or disp...

SKU: DF-SEN0596 · MPN: SEN0596

##Introduction This carbon monoxide gas sensor differs from most gas sensors on the market as it does not provide specific gas concentration data. Instead, it detects whether the surrounding environment exceeds or falls below a fixed threshold. It operates on a wide voltage range of 5-24V, with h...

SKU: DF-SEN0595 · MPN: SEN0595

##Introduction This formaldehyde gas sensor differs from most gas sensors on the market as it does not provide specific gas concentration data. Instead, it detects whether the surrounding environment exceeds or falls below a fixed threshold. It operates on a wide voltage range of 5-24V, with high...

SKU: AF-5382

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also if say you want to JTAG program a board that you can't solder headers to.Most pog...

SKU: AF-5381

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also if say you want to JTAG program a board that you can't solder headers to.Most pog...

SKU: AF-2787

A pack of 25 through-hole 100 kΩ resistors — an essential component for voltage dividers, pull-up/pull-down circuits, and general electronics projects. The 0.4 mm lead diameter fits standard solderless breadboards perfectly. Specifications Resistance – 100 kΩ Tolerance – ±5% Power Rating – ¼...

SKU: AF-4293

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you!This is a 25 Pack of 100Ω Resistors. More specifically, they are carbon film, through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistors...

SKU: AF-2784

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 10K Ω Resistors. More specifically, they are carbon film, through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% pre...