All Products

SKU: DF-SEN0159

The Gravity CO2 Gas Sensor uses an MG-811 electrochemical sensing element to detect carbon dioxide concentration in the air. The output voltage decreases as CO2 concentration increases, and an onboard potentiometer lets you set a threshold for a digital on/off signal output. An onboard heating c...

SKU: DF-SEN0134

The Gravity MQ-9 gas sensor detects carbon monoxide (CO) and combustible gases including methane and propane. It uses a semiconductor SnO2 sensing element that cycles between high and low temperatures — detecting CO at low temperature (1.5V) and combustible gases at high temperature (5.0V). With...

SKU: DF-DFR0332

Make an air aerial propeller vessel, a cooling system, or spinning machine with this small fan module. It comes with a propeller, a 15,000 rpm motor and cable. Add flavor to your own interesting projects with this module. This module is commonly used for STEM class. SPECIFICATIONS ...

SKU: DF-DFR0430

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecting it to the MCU and learning the relevant electronic theory can be confusing and frustrating when you ju...

SKU: DF-DFR0067

This Gravity-compatible DHT11 sensor provides calibrated digital temperature and humidity readings via a single data pin. With an integrated 8-bit microcontroller and factory-calibrated coefficients stored in OTP memory, it delivers reliable measurements with minimal setup. The Gravity 3-pin int...

SKU: DF-DFR0032

Here is the simplest sound making module that you can use High/Low to drive it. Just change the frequency it buzz, you can hear different sound. It is widely used on your daily application, like PC, refrigerator,phones and so on. And you also can create many interesting interactive project w...

SKU: DF-SEN0192

INTRODUCTION The microwave sensor applies the Doppler effect to detect moving objects using microwaves. This differs from the method used by a regular infrared (IR) sensor as microwave is sensitive to a variety of objects that are microwave-reflective, and its sensor...

SKU: DF-SEN0216

The Water Flow sensor measures the rate of a liquid flowing through it. The YF-S401 water flow sensor consists of a plastic valve body, flow rotor and hall effect sensor. It is usually used at the inlet end to detect the amount of flow. When liquid flows through the sensor, a magnetic rotor w...

SKU: DF-SEN0160

A digital weight sensor kit based on the HX711 24-bit ADC, capable of measuring up to 1 kg. The HX711 is designed specifically for weight scale applications, interfacing directly with a bridge sensor to deliver precise, reliable measurements via the Gravity interface. The kit includes both the H...

SKU: DF-DFR0300

The Gravity EC (Electrical Conductivity) Sensor measures the conductivity of aqueous solutions, providing an analogue output for Arduino and compatible microcontrollers. EC measurement is essential for monitoring water quality, nutrient levels in hydroponic systems, and soil salinity in agricultu...

SKU: DF-SEN0127

  INTRODUCTION This is a generic Arduino gas sensor. It has MQ2 probe which is able to detect LPG, i-butane, propane, methane ,alcohol, Hydrogen, smoke.It can be used in gas leakage detecting device in consumer and industry markets. It has a high sensitivity and fast response time. ...

SKU: DF-SEN0213

The DFRobot Gravity Heart Rate Monitor Sensor measures the electrical activity of the heart and outputs it as an analog signal. Built around the AD8232 chip, it filters and amplifies the ECG signal to produce a clean waveform from the PR and QT intervals — viewable in real time using the Arduino ...

SKU: DF-SEN0133

This is an Arduino hydrogen gas sensor. It has high sensitivity to Hydrogen (H2) and less sensitivity to alcohol, LPG,cooking fumes . Hydrogen gas is highly flammable and will burn in air at a very wide range of concentrations The sensitivity is able to be adjusted by the potentiome...

SKU: DF-SEN0018

This is a simple to use arduino motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low. This sensor checks for infrared heat in it's detecting angle. Human body, pets and several ot...

SKU: DF-DFR0023

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a functional range between 0 degree Celsius to 100 degree Celsius with a sensitivity ...

SKU: DF-SEN0129

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smoke. The sensitivity can be adjusted by the potentiometer. The output is ...

SKU: DF-SEN0130

The Gravity MQ5 gas sensor is highly sensitive to LPG, natural gas, and town gas, with lower sensitivity to alcohol, cooking fumes, and cigarette smoke. The analogue output is proportional to gas concentration, and sensitivity can be adjusted via the on-board potentiometer. Gravity interface for ...

SKU: DF-SEN0165

In the ever-increasing need and awareness for health and safety, water has become a focus point for proper disinfection treatment as aftereffects of industrialization can become a danger for contamination of water via direct contact. Water is a critical control point of contact where proper t...

SKU: DF-SEN0161

You may check the latest version - Gravity: Analog pH Sensor/Meter Kit V2 to meet your requirements and Liquid Sensor Selection Guide to get better familiar with our liquid sensor series.Need to measure water quality and other parameters but haven't got any low-cost pH meter? Find it difficult t...

SKU: DF-SEN0169

This is a professional Arduino pH Sensor Meter Kit with industrial electrode. It has built-in simple, convenient , practical connection and long life (up to 1 year), which makes it very suitable for long term online monitoring. It has an LED which works as the Power Indicator, a BNC connector...