SparkFun

SKU: SF-PRT-10738 | Brand: SparkFun

These metal hex standoffs raise your development board or proto board off the work surface for protection and airflow. With a #4-40 thread, they fit most boards with standard mounting holes. Specifications Length: ...

SKU: SF-PRT-10739 | Brand: SparkFun

Metal short standoffs: 3/8" long x ¼"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available holes. Don’t forget the screws! Related below. Note: These are sold as a...

SKU: SF-KIT-12963 | Brand: SparkFun

The SparkFun Digital Sandbox Add-On kit extends the Digital Sandbox (DS) learning platform with three additional circuit experiments. Build an electric musical instrument, control motor speed, and drive a servo — perf...

SKU: SF-DEV-10618 | Brand: SparkFun

The SparkFun Power Driver Shield Kit lets you switch high-current loads directly from your Arduino using six RFP30N06LE N-channel MOSFETs. Connect a computer power supply or other DC source to drive motors, solenoids,...

SKU: SF-BOK-10626 | Brand: SparkFun

Want to build your own robots, turn your ideas into prototypes, or control devices with a computer? It’s a snap with this book and the Arduino open source electronic prototyping platform. Get started with six fun proj...

SKU: SF-BOB-12886 | Brand: SparkFun

If you aren’t familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both to other devices and to internet services. The SparkFun Electric Imp Breako...

SKU: SF-BOB-10496 | Brand: SparkFun

This is a breakout board to allow simple access to the tightly pitched pins on the GS406 and GS407 GPS units. This board breaks out all of the necessary pins to a row of standard 0.1" spaced header to allow for easy b...

SKU: SF-PRT-10463 | Brand: SparkFun

Metal Hex Male/Female standoffs. #4-40 thread with 3/8" shank and 3/16" thread length. Can be stacked to create any length. Pack of 10

SKU: SF-DEV-10406 | Brand: SparkFun

This board is an evaluation platform for the SM130 RFID module. It includes an XBee header, PCB trace antenna, and has the layout to be used as a shield for an Arduino. There is a small prototyping area as wel...

SKU: SF-SEN-12784 | Brand: SparkFun

This is the SparkFun “Time-of-Flight” Range Finder, a breakout for the VL6180 distance sensor. Unlike most distance sensors that rely reflected light intensity or reflected angles to determine range, the VL6180 use...

SKU: SF-PRT-12791 | Brand: SparkFun

This is a 2x23 pin male PTH header. This piece is in the common configuration for Beaglebone Black headers that can be broken apart to form smaller header formations. Each pin has a spacing of 0.1" in between each oth...

SKU: SF-DEV-12761 | Brand: SparkFun

The SparkFun microSD Shield gives your Arduino mass-storage capability via a microSD card slot, making it ideal for data-logging and projects that need to read or write files. Communication with the microSD card uses...

SKU: SF-PRT-10359 | Brand: SparkFun

This is a simple four wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 4-pin JST SH connector on ...

SKU: SF-SEN-12728 | Brand: SparkFun

Infrared proximity sensor made by Sharp. Part # GP2Y0A41SK0F has an analog output that varies from 3.1V at 4cm to 0.3V at 30cm with a supply voltage between 4.5 and 5.5VDC. The sensor has a Japanese Solderless Termina...

SKU: SF-PRT-12718 | Brand: SparkFun

PCB mount clip to hold a AAA battery. Sold in single units, you’ll need two for each battery. These work great for small, low power applications that need a battery to run. Low cost and easy to use!Documents:Datasheet

SKU: SF-BOB-12708 | Brand: SparkFun

This is the SparkFun Real Time Clock (RTC) Module, this little breakout that uses the DS1307 to keep track of the current year, month, day as well as the current time. The module comes fully assembled and includes a s...

SKU: SF-ROB-12629 | Brand: SparkFun

The DAGU Wheel Encoder Kit is a simple add-on for wheeled robots that measures speed and distance travelled. Each kit includes two neodymium 8-pole magnets with rubber hubs and two hall-effect sensors, providing relia...

SKU: SF-SEN-12617 | Brand: SparkFun

Knowing where your robot is can be very important! The RedBot Wheel Encoder allows you to track the number of revolutions each wheel has made. This sensor works by detecting the movement of small teeth connected to a ...

SKU: SF-ROB-12605 | Brand: SparkFun

These continuous rotation 3:1 gear ratio channel gearbox kits incorporate threaded side mounts to easily attach a standard size servo to numerous Actobotics products including tubing and channel; making it easy to ...

SKU: SF-ROB-12600 | Brand: SparkFun

These 360° rotation 3:1 gear ratio channel gearbox kits incorporate threaded side mounts to easily attach a standard size servo to numerous Actobotics products including tubing and channel; making it easy to incorp...