SparkFun

SKU: SF-CAB-12977 | Brand: SparkFun

This is a USB to TTL Serial Cable which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this cable are configured to operate at 3.3V specifically with a Raspberry Pi with each serial p...

SKU: SF-CAB-10647 | Brand: SparkFun

Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look more finished than a nice clean wiring harness.This is a 15ft. length ...

SKU: SF-COM-10633 | Brand: SparkFun

A large 10 mm through-hole LED with a diffused green glow. The opaque epoxy package produces a soft, even light output that's easy to see from wide viewing angles — perfect for indicators, prototyping, and decorative ...

SKU: SF-DEV-12898 | Brand: SparkFun

The SparkFun MIDI Shield board gives your Arduino-based device access to the antiquated, but still widely used and well supported MIDI communication protocol, so you can control synthesizers, sequencers, and other ...

SKU: SF-PRT-12900 | Brand: SparkFun

This is an incredibly simple two cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fair since that is what they have been primarily used for. However, with...

SKU: SF-KIT-10547 | Brand: SparkFun

This is the latest version of our popular through-hole Simon Says Kit. We’ve made some changes to the board that should make it easier than ever for the beginner to build! All components are through-hole, making this ...

SKU: SF-COM-12877 | Brand: SparkFun

We know this looks like a lot of our other LEDs, but it’s not! This is a PTH Addressable RGB LED with a WS2812 control IC built right into the LED. This PTH version is incredibly similar to its SMD cousin, except it i...

SKU: SF-ROB-12859 | Brand: SparkFun

The Big Easy Driver is a stepper motor driver board for bipolar stepper motors up to 2 A per phase, based on the Allegro A4988 driver chip. Designed by Brian Schmalz, it's the successor to the popular Easy Driver boar...

SKU: SF-TOL-10405 | Brand: SparkFun

This sewing needle set is designed for e-textile projects, with eye sizes large enough to easily thread conductive thread. The set includes both large and small needles to suit different stitching needs — from thick f...

SKU: SF-ROB-12779 | Brand: SparkFun

The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The EasyDriver requires a 6V to...

SKU: SF-BOB-12758 | Brand: SparkFun

The SparkFun Electret Microphone Breakout pairs a small electret microphone capsule with a 60× OPA344 op-amp preamplifier, making it easy to detect sound with a microcontroller's analogue-to-digital converter. Pick up...

SKU: SF-SEN-10289 | Brand: SparkFun

This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don’t touch, thus not making a...

SKU: SF-SEN-10245 | Brand: SparkFun

A single-point load cell (strain gauge) rated for up to 50 kg. This is the same type of sensor found in digital bathroom scales. It outputs a small analogue voltage proportional to the applied force, which can be read...

SKU: SF-PRT-12639 | Brand: SparkFun

A 3.5mm TRRS (tip, ring, ring, sleeve) audio jack in a surface-mount package. Unlike standard stereo TRS connectors, TRRS provides three conductors plus ground, allowing it to carry stereo audio along with an addition...

SKU: SF-TOL-12572 | Brand: SparkFun

These are nice, cross-locking, curved tweezers, unlike traditional models the tips on these tweezers will remain closed until squeezed open. They have a very fine tip which allows you to pick up very small parts with ...

SKU: SF-DEV-09873 | Brand: SparkFun

The SparkFun FTDI Basic Breakout provides USB-to-serial conversion using the FTDI FT232RL IC, operating at 3.3V logic levels. Its 6-pin header matches the standard FTDI pinout, making it compatible with Arduino Pro, L...

SKU: SF-CAB-09741 | Brand: SparkFun

These are good quality IC test hooks with a male connection wire. Instead of a single hook, these have two hooks that are capable of grabbing very small points (like SOIC IC legs). Comes in a bag of five IC hooks of d...

SKU: SF-PRT-09599 | Brand: SparkFun

A 5g syringe of white thermal compound (also known as thermal grease or thermal paste) for improving heat transfer between components and heatsinks. Essential for any project where heat dissipation is critical. Compo...

SKU: SF-PRT-08431 | Brand: SparkFun

This is a SparkFun exclusive! These are 155mm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Combine these with our female to femal...

SKU: SF-DEV-24870 | Brand: SparkFun

The SparkFun RP2350 Pro Micro provides a powerful development platform in SparkFun's compact Pro Micro form factor, built around the RP2350 from the Raspberry Pi Foundation. This board uses the updated Pro Micro form ...