Sound & Audio

SKU: SF-PRT-08032 | Brand: SparkFun

Low profile 3.5mm stereo audio jack.Documents:Audio 3.5mm Jack Datasheet

SKU: DF-DFR1173 | Brand: DFRobot

This compact voice prompt module integrates an intelligent MP3 playback chip with a 1 W speaker in a tiny 30 × 11 mm package. It supports MP3, WAV, and WMA hardware decoding with 16 MB of on-board storage that retains...

SKU: DF-DFR0719 | Brand: DFRobot

A compact Bluetooth 5.0 audio receiver board that turns any wired speaker into a wireless one. Simply connect power (3.7–24V) and wire up your speaker — pair it with your phone and start streaming music wirelessly. Th...

SKU: DF-DFR0745 | Brand: DFRobot

Wanna buy a simple & practical voice recorder? This one is right for you! The voice recorder module supports 4 controlling modes (Arduino, AT command, on-board buttons, and ADKEY), and multi-segment voice recording. Y...

SKU: EC-ASVS1053MP | Brand: Elecrow

An Arduino-compatible MP3 shield based on the VS1053B audio codec from VLSI. It decodes all major audio formats — including MP3, OGG Vorbis, AAC, WMA, FLAC, WAV, and MIDI — and can record in Ogg Vorbis, IMA ADPCM, and...

SKU: SF-COM-09151 | Brand: SparkFun

A compact 0.5W speaker with 8 ohm impedance, small enough to fit inside robot builds, enclosures, and portable electronics projects. Suitable for audio output from amplifier boards, microcontrollers with DAC/PWM audio...

SKU: SF-WIG-13660 | Brand: SparkFun

The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the WAV Trigger can p...

SKU: SF-DEV-13116 | Brand: SparkFun

The SparkFun Spectrum Shield splits a stereo audio input into 7 frequency bands per channel using two MSGEQ7 graphic equaliser ICs. Read the amplitude of each band via your Arduino's ADC to create sound-reactive proje...

SKU: SF-DEV-12898 | Brand: SparkFun

The SparkFun MIDI Shield board gives your Arduino-based device access to the antiquated, but still widely used and well supported MIDI communication protocol, so you can control synthesizers, sequencers, and other ...

SKU: SF-PRT-12639 | Brand: SparkFun

A 3.5mm TRRS (tip, ring, ring, sleeve) audio jack in a surface-mount package. Unlike standard stereo TRS connectors, TRRS provides three conductors plus ground, allowing it to carry stereo audio along with an addition...

SKU: DF-DFR0034 | Brand: DFRobot

This is a new Arduino compatible Analog Sound Sensor. Sound Sensor is typically used in detecting the loudness in ambient, the Arduino can collect its output signal and actuate accordingly. You may use it to make some...

SKU: LB-LS6972x2 | Brand: Little Bird

A compact stereo speaker pair for small audio projects, handheld devices, and embedded builds. Each 45mm driver is rated at 4Ω and 3W, delivering clear, balanced sound in a slim form factor. Pre-wired with a PH2.0 plu...

SKU: SF-PRT-20660 | Brand: SparkFun

This is a small 15mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces.This through-hole speaker is great for projects where you don't have...

SKU: PR-PIM356 | Brand: Little Bird

Add sound to your micro:bit projects with noise:bit, a tiny speaker board made for bleeps, bloops, tones and speech.Just slot in your micro:bit and use the sound generation blocks and code in Microsoft MakeCode or Mic...

SKU: AF-1313 | Brand: Adafruit

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm a...

SKU: AF-1732 | Brand: Adafruit

A high-power 4" (102mm) full-range speaker rated at 20W continuous with 4Ω impedance. The wide frequency response of 60Hz–24kHz delivers clear audio across the full spectrum, making it suitable for projects where you ...

SKU: AF-2210 | Brand: Adafruit

The Adafruit Audio FX Sound Board with 2×2W Amp is a standalone audio trigger with a built-in stereo Class D amplifier — no Arduino or programming required. Simply drag and drop WAV or OGG sound files over USB, wire u...

SKU: AF-2790 | Brand: Adafruit

A 3.5 mm (1/8") stereo (TRS) audio plug with screw terminal connections — no soldering required. Use stranded or solid-core wire and a small screwdriver to create custom audio cables, breakouts, and test leads. This ...

SKU: SF-COM-08635 | Brand: SparkFun

Small electret microphone. Useful in acoustic and audio applications. Documents: Datasheet Example Audio LED control project by Adam Greig

SKU: SF-COM-07950 | Brand: SparkFun

This is a small 12mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces.This is not a true piezoelectric speaker but behaves similarly. Inst...