Prototyping

SKU: SF-COM-15105 | Brand: SparkFun

This diode-transistor photocouplers consist of an LED, optically coupled to a high speed photodetector to transmit electrical signals between circuits while still isolating your system from higher voltages. The 6N137 ...

SKU: SF-COM-14978 | Brand: SparkFun

This little round on/off/on toggle switch is rated up to 10A at 125VAC and can be panel mounted in a 20mm diameter hole. It’ll also look pretty slick in your project!

SKU: AF-3642 | Brand: Adafruit

A 2.1 mm DC barrel jack with a built-in slide switch, giving you simple on/off control for devices that lack a dedicated power switch. It shares the same PCB footprint as a standard non-switched barrel jack, so it dro...

SKU: AF-2164 | Brand: Adafruit

The classic L7805 linear voltage regulator in a TO-220 package, capable of delivering a clean, regulated 5.0 V output (±2%) from an input voltage of 7–35 V. With built-in current limiting and thermal shutdown protecti...

SKU: AF-2448 | Brand: Adafruit

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel ...

SKU: DF-FIT0216 | Brand: DFRobot

A compact, spring-loaded desoldering pump (solder sucker) for removing solder from PCB joints and through-holes. The ProsKit DP-366D features a double oil-sealed piston for guaranteed leak-free suction and a soft foam...

SKU: SF-COM-09117 | Brand: SparkFun

This is a 12-step rotary encoder with a nice ‘clicking’ feel. It’s breadboard friendly, and has a pretty handy select switch (by pushing in on the knob). The encoder is different from a potentiometer in that an enc...

SKU: DF-FIT0296 | Brand: DFRobot

A 150mm servo extension cable for reaching servos mounted further from the controller than the servo's built-in lead allows. Male connector plugs into the controller, female connector mates with the servo. Also works ...

SKU: SF-BOB-14021 | Brand: SparkFun

This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each bo...

SKU: DF-FIT0244 | Brand: DFRobot

A pack of 50 basic 3mm LEDs in five colours — 10 each of red, green, yellow, white, and blue. Handy for prototyping, indicator lights, and Arduino projects. Specifications Forward Voltage – 1.8–2.2V Max Current – ...

SKU: SF-PRT-08272 | Brand: SparkFun

This 2 mm pitch 10-pin socket mates with XBee radio modules from Digi, allowing you to mount your XBee without soldering it directly to a PCB. You'll need two of these sockets to connect to all 20 pins on an XBee modu...

SKU: DF-FIT0323 | Brand: DFRobot

This 100-piece assortment gives you a handy spread of common through-hole diodes for prototyping, repairs and general project builds. It covers small-signal diodes, standard rectifiers, fast-recovery diodes and Schott...

SKU: SF-COM-00533 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: SF-PRT-00132 | Brand: SparkFun

Through-hole RJ11 socket with PCB mounting posts. 6-pin connection - housing accepts common telephone connectors/wiring. If you need a board for this connector be sure to check out our SparkFun RJ11 Breakout. Two b...

SKU: AF-3057 | Brand: Adafruit

Polyimide Tape (sometimes referred to by the brand name Kapton Tape) is an interesting addition to your toolbox! Polyimide Tape remains stable across a wide range of temperatures from about −269°C to +400°C.&n...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...