Prototyping

SKU: DF-FIT0323 | Brand: DFRobot

This 100-piece assortment gives you a handy spread of common through-hole diodes for prototyping, repairs and general project builds. It covers small-signal diodes, standard rectifiers, fast-recovery diodes and Schott...

SKU: SF-COM-00533 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...

SKU: PL-1928 | Brand: Pololu

This crimping tool can be used to crimp both male and female versions of our Tamiya connector crimp pins, mini Tamiya connector crimp pins, JST RCY connector crimp pins, JR crimp pins, Futaba J crimp pins, and crimp p...

SKU: SF-COM-12903 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well too bad, you are getting two of each!...

SKU: SF-PRT-10571 | Brand: SparkFun

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.Documents: Datasheet

SKU: AF-756 | Brand: Adafruit

Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics such as small motors, solenoids, or IR LEDs. We find them so handy, th...

SKU: AF-3393 | Brand: Adafruit

A dual-ganged 10K linear potentiometer with a built-in on/off switch — two components in one convenient panel-mount package. The dual 10 kΩ linear-taper pots share a grippy shaft that turns smoothly without shifting o...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: LB-LS000A | Brand: Little Bird

A pack of 30 tactile pushbutton switches in six vibrant colours — blue, white, yellow, green, black, and red. Each 12mm switch comes with a snap-on square cap, making it easy to create colour-coded controls for your p...

SKU: LB-LS6511 | Brand: Little Bird

A 30-metre kit of flexible silicone hook-up wire in red and black, ideal for power wiring in electronics projects. The 22AWG gauge suits a wide range of applications from breadboard prototyping to permanent installati...

SKU: TB-HM3194 | Brand: Little Bird

A 12-way screw terminal strip rated at 6A and 250VAC. Can be divided into smaller sections with a sharp knife, making it easy to create custom-sized terminal blocks for any project. Each terminal block includes a moun...

SKU: LB-LS3506 | Brand: Little Bird

This 2×20 pin extra tall male GPIO header stands 12 mm high, providing additional clearance when soldering onto HATs, Bonnets, or custom boards for Raspberry Pi. It's ideal for boards that don't come with headers pre-...

SKU: AF-5487 | Brand: Adafruit

These ultra-fine wired LEDs are designed for model-makers and crafters but they could also come in handy for folks who want to add tiny points of light to a design without needing SMT-level soldering skills. Use ...

SKU: LB-LS3381-W | Brand: Little Bird

A 12 mm panel-mount momentary push button with a smooth dome-shaped cap in white, pre-wired with 20 cm red and black leads for easy connection. Normally open — pressing the button closes the contacts. Key Features ...

SKU: DF-FIT0861 | Brand: DFRobot

A set of five solderless snap-down connectors for joining 10 mm wide, 3-wire LED strips without soldering. Simply align the strip's copper pads with the connector contacts and snap the cover down for a firm electrical...