Jumpers & Wires

SKU: SF-PRT-08671 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opposite end. Dimensions: 100mm length Documents: JST connector

SKU: SF-PRT-08024 | Brand: SparkFun

Standard 22 AWG solid Yellow hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes in small spools of 25'.

SKU: SF-WRL-00662 | Brand: SparkFun

This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the our WiFly Shield.Dimensions: 4" LengthDocuments: Datasheet RF Connector Buying Guide

SKU: SF-PRT-11864 | Brand: SparkFun

This Deans (mini T-plug) connector pair provides a secure, high-current connection rated up to 30A. Widely used in R/C vehicles, battery packs, and power distribution, the polarised design prevents reverse-polarity co...

SKU: DF-FIT0334 | Brand: DFRobot

This 300mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors, which means it is co...

SKU: AF-238 | Brand: Adafruit

This is a interface cable designed for Bus Pirate which can makes it easier to connect the Bus Pirate to a circuit and get hacking!

SKU: SF-PRT-11363 | Brand: SparkFun

A set of three common gauges of enameled magnet wire for winding transformers, chokes, motors, and electromagnet experiments. The thin enamel coating insulates each wire, allowing tight coil windings without short cir...

SKU: AF-3142 | Brand: Adafruit

Our Raw Male/Male Jumper Wires are perfect for making a custom jumper wire sets for wire harnesses or jumpering between headers on PCB's. These premium jumpers are a little over 6" (150mm) long and come in a 'strip...

SKU: AF-3145 | Brand: Adafruit

A pack of 50 small single-row wire housings for building custom jumper cable harnesses. Compatible with both male and female crimp pins, these housings let you create exactly the wire configurations your project needs...

SKU: AF-3146 | Brand: Adafruit

Create custom wire harnesses with these single-row housings for DIY jumper cables. Compatible with both male and female jumper wires, these housings give you full control over your wiring layout and connector configur...

SKU: SF-PRT-13164 | Brand: SparkFun

This is a simple three wire cable. Each cable is 6" long and is great for jumping from board to board or just about anything else. There is a 3-pin JST connector with 0.1" spacing on both ends. These jumper wires come...

SKU: AF-3111 | Brand: Adafruit

This is a box of six 25ft spools of stranded-core wire. Stranded-core wire is best used for wiring jigs where there's bending or movement expected. It also works well with terminal blocks. It's no...

SKU: SF-PRT-10373 | Brand: SparkFun

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway he...

SKU: SF-PRT-10363 | Brand: SparkFun

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway heade...

SKU: AF-760 | Brand: Adafruit

A 40-piece set of premium male-to-male jumper wires in a rainbow ribbon cable format. Each wire is 12″ (300mm) long with 0.1″ (2.54mm) male header contacts on both ends, fitting cleanly on standard-pitch headers and b...

SKU: SF-PRT-09916 | Brand: SparkFun

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST connector on one end, bare cable on the opposite end. It also comes with the mating connector f...

SKU: AF-793 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" female ...

SKU: AF-1955 | Brand: Adafruit

These Male/Male Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbo...

SKU: SF-CAB-09556 | Brand: SparkFun

This is an interface cable for the Bus Pirate, designed to connect to its 2x5 I/O header. The cable’s connector is composed of two rows of five 0.1" spaced pins; it’s also polarized, as is the mating connector on-b...

SKU: SF-PRT-09385 | Brand: SparkFun

A pack of 10 premium 12″ (30 cm) male-to-female jumper wires for breadboarding, prototyping, and connecting to 0.1″ pitch headers. Each wire has a male pin on one end and a female socket on the other, making them vers...