Brands and Manufacturers

SKU: AF-3062 | Brand: Adafruit

Complete your Pi setup with our custom designed faceplate specifically designed to fit your 2.8" PiTFT and Adafruit Pi B+ / Pi 2 / Pi 3 case base! This Clear Case Base and Faceplate and Buttons Combo&nbsp...

SKU: AF-424 | Brand: Adafruit

A six-piece precision screwdriver set covering the most common sizes found in consumer electronics, small devices, and maker projects. The set includes three Phillips and three flat-head drivers in a compact carrying ...

SKU: SF-DEV-10914 | Brand: SparkFun

It’s blue! It’s skinny! It’s the Arduino Pro! SparkFun’s minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Because the system voltage for this board is lower than other Arduino...

SKU: AF-425 | Brand: Adafruit

A 4-pin Molex power cable that matches the hard drive/CD-ROM power connectors found on AT and ATX power supplies. Use it to tap into 5V or 12V DC from a desktop power supply for your projects — a convenient source of ...

SKU: SF-PRT-13061 | Brand: SparkFun

This 6 position screw terminal block provides a simple way to connect wires to a single connection point. These blocks allow wires to be screwed together and self-isolated without needing to twist, solder or any other...

SKU: SF-KIT-13053 | Brand: SparkFun

Holy Wattage, Batman! This Power Resistor Kit comes with 5 each of 5 different 10 Watt resistor values including 1, 2, 4, 8, and 16 Ohms. These resistors are capable of dissipating large amounts of power without damag...

SKU: DF-DFR0352 | Brand: DFRobot

This standard sheild for WRTnode is directly stackable with the WRTnode Mini OpenWRT Dev Board. WRTnode (A Mini OpenWRT Dev Board) uses a MTK MT7620N 580MHZ MIPS CPU, and is powerful in both interface an...

SKU: SF-ROB-10848 | Brand: SparkFun

These steppers have a threaded shaft, which allows them to be used as a linear actuator. As the motor runs, it moves along the shaft at a specific rate of 1cm per 5 full rotations. These are a good choice for linear m...

SKU: SF-PRT-10853 | Brand: SparkFun

This is a wire assembly terminated with the same 8-pin JST-SH connector which is on the Mega Pro Mini. Pick up a few of these to break out all of those pesky pins. Integrating these connectors into your projects ma...

SKU: AF-443 | Brand: Adafruit

For really big projects, give yourself some room to work in, with a massive 2250-point breadboard - equivalent in size to three full sized breadboards side by side.The breadboards are mounted onto a metal plate, and ...

SKU: AF-454 | Brand: Adafruit

You will squeak with delight when you hold this adorable miniature LED 8x8 matrix. 0.8" square, it's got everything a big LED matrix has, but bite-sized! There are 16 pins on the side, 8 on each, with 0.1" spacing ...

SKU: AF-415 | Brand: Adafruit

EL tape is the flat, wide cousin of EL wire — same glowing effect but in a 1cm-wide strip format. The glowing surface is 1cm wide (plastic coating is about 1.5cm), with adhesive on the back for easy mounting. Covered ...

SKU: AF-475 | Brand: Adafruit

This 30mm translucent green arcade button features a crystal-clear glossy finish and smooth button action. A pre-installed micro-switch with gold-plated contacts provides a satisfying press with tactile feedback — no ...

SKU: AF-3270 | Brand: Adafruit

Adafruit offers fun and exciting stickers for achievement in electronics, science and engineering. We believe everyone should be able to be rewarded for learning a useful skill, a sticker is just one of the...

SKU: SF-CAB-10759 | Brand: SparkFun

Integrating Ethernet support into your project is a great way to relay data through a local area network and even bounce information out to the internet. Sometimes it’s hard to get power to your Ethernet devices. Woul...

SKU: SF-SEN-10740 | Brand: SparkFun

An evaluation board for the MLX90614 non-contact infrared thermometer sensor. It pairs the MLX90614 with an ATmega328 running at 3.3 V (8 MHz Arduino bootloader), giving you a ready-to-use IR temperature sensor with s...

SKU: AF-498 | Brand: Adafruit

This is a fancy upgrade to standard 20x4 LCDs, instead of just having blue and white, or red and black, this LCD has full color RGB characters on a dark/black background! That means you can change the character displa...

SKU: SF-PRT-10739 | Brand: SparkFun

Metal short standoffs: 3/8" long x ¼"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available holes. Don’t forget the screws! Related below. Note: These are sold as a...

SKU: AF-499 | Brand: Adafruit

This 20×4 character LCD features black text on a full-colour RGB backlight that you can set to any colour — red, green, blue, purple, teal, white, and everything in between. It's the most daylight-readable character L...

SKU: AF-3315 | Brand: Adafruit

A 2.4" TFT touchscreen display shield for the Adafruit Feather ecosystem. Featuring a 320×240 pixel display with 16-bit colour, a resistive touchscreen, and a built-in microSD card slot, this FeatherWing adds a full i...