Brands and Manufacturers

SKU: SF-CAB-10649 | Brand: SparkFun

A 3-foot (approximately 90 cm) length of 10-wire ribbon cable. Useful for making clean, organised multi-conductor connections in electronics projects — ideal for connecting to IDC crimp-on connectors. Specifications ...

SKU: AF-3317 | Brand: Adafruit

The Adafruit VL53L0X is a Time-of-Flight (ToF) distance sensor from ST that uses an invisible laser to measure distances from approximately 50 mm to 1200 mm. By timing how long the laser light takes to bounce back, it...

SKU: SF-COM-10349 | Brand: SparkFun

The FQP27P06 is a P-channel enhancement-mode power MOSFET rated for −60V and −27A. With a very low on-resistance of 70 mΩ and a gate threshold compatible with 5V logic, it is well suited for high-side switching contro...

SKU: AF-1831 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will...

SKU: AF-1891 | Brand: Adafruit

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (pr...

SKU: AF-641 | Brand: Adafruit

A 3-ply conductive thread made entirely from 316L stainless steel fibre. Thin enough to sew by hand with a medium-eye needle, yet strong and smooth — ideal for wearable electronics, e-textile projects, and sewable cir...

SKU: DF-DFR0406 | Brand: DFRobot

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two...

SKU: SF-BOB-12700 | Brand: SparkFun

This simple breakout board routes a female USB Type-A connector's VCC, GND, D−, and D+ pins to a standard 0.1″ pitch header. It saves you the hassle of soldering tiny SMD connectors when adding USB host or device conn...

SKU: AF-3406 | Brand: Adafruit

The Feather nRF52 Bluefruit LE is an all-in-one Bluetooth Low Energy development board built around the Nordic nRF52832. Unlike earlier Bluefruit Feathers that used a separate helper chip, the nRF52832 runs your appli...

SKU: SF-BOB-10031 | Brand: SparkFun

We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping nee...

SKU: AF-759 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male head...

SKU: AF-1982 | Brand: Adafruit

The Adafruit MPR121 Capacitive Touch Sensor Breakout provides 12 channels of capacitive touch sensing over I2C. The MPR121 handles all the capacitive filtering internally and can be configured for varying sensitivity ...

SKU: SF-COM-09772 | Brand: SparkFun

A standard 5 × 20 mm glass cartridge fuse rated at 5A / 125V AC. When current exceeds 5A, the internal filament breaks and opens the circuit, protecting your electronics from overcurrent damage. Compatible with standa...

SKU: AF-1952 | Brand: Adafruit

These premium female-to-male extension jumper wires are ideal for making wire harnesses or extending connections between headers on PCBs. Each strip contains 20 wires (2 of each rainbow colour) in a convenient ribbon ...

SKU: AF-1967 | Brand: Adafruit

This fully assembled mini pan-tilt kit provides two-axis motion using two included micro servos (SG-90 or SG-92 type). The mechanism pans approximately 180° side to side and tilts approximately 150° up and down, givin...

SKU: SF-PRT-09541 | Brand: SparkFun

The BPW34 is a tiny, general purpose PiN photodiode. This photodiode has a ton of uses, one of which is to use it is a mini solar cell to power your project. The cell is sensitive to a wide range of light wavelengths ...

SKU: DF-DFR0067 | Brand: DFRobot

This Gravity-compatible DHT11 sensor provides calibrated digital temperature and humidity readings via a single data pin. With an integrated 8-bit microcontroller and factory-calibrated coefficients stored in OTP memo...

SKU: AF-875 | Brand: Adafruit

This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. U...

SKU: AF-3481 | Brand: Adafruit

A panel-mount 10 kΩ logarithmic potentiometer with an integrated on/off switch. The logarithmic taper is designed for audio volume control — resistance increases on a curve that matches how the human ear perceives lou...

SKU: AF-2047 | Brand: Adafruit

A soft-touch T18 potentiometer knob in white with a rubbery grip for comfortable, precise adjustment. Features a white indicator line on the outside for clear position visibility. Designed to press-fit directly onto T...