Brands and Manufacturers

SKU: AF-1131 | Brand: Adafruit

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs includin...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: AF-1405 | Brand: Adafruit

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic pr...

SKU: AF-3930 | Brand: Adafruit

This Reflective IR Sensor is a simple plastic casing with two elements - an IR LED and an IR phototransistor. You can control the IR LED and turn it on to bounce IR off objects to determine their reflectivity. Whit...

SKU: AF-3686 | Brand: Adafruit

Breathe easy, knowing that you can track and sense the quality of the air around you with the PM2.5 Air Quality Sensor with Breadboard Adapter particulate sensor. Mad Max & Furiosa definitely should have ho...

SKU: AF-1669 | Brand: Adafruit

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclos...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-2324 | Brand: Adafruit

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell ba...

SKU: AF-2430 | Brand: Adafruit

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also i...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: AF-2717 | Brand: Adafruit

The TCA9548A 1-to-8 I2C multiplexer solves the common problem of needing multiple I2C devices with the same address on a single bus. It acts as a gatekeeper, routing I2C traffic to any of its eight downstream channels...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: DF-FIT0314 | Brand: DFRobot

NFC Tag (13.56MHz) is widely used in electronic locks or customer identification as well as other systems where a small and easy to carry tag is desired.The tag contains a NXP S50 chip and an antenna, and is passi...

SKU: SF-PRT-11895 | Brand: SparkFun

A standard 8-pin female header with 0.1" (2.54 mm) pitch, designed for through-hole mounting. Connects with most standard 8-pin male headers. Specifications Pins – 8 Pitch – 0.1" (2.54 mm) Type – Female, through-...

SKU: SF-DEV-13903 | Brand: SparkFun

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure to sew into clothing or whatever else you can dream up.The LilyPad Rai...