Brands and Manufacturers

SKU: AF-1381 | Brand: Adafruit

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can al...

SKU: DF-SEN0232 | Brand: DFRobot

The Gravity Analog Sound Level Meter is an Arduino-compatible decibel meter that accurately measures environmental noise levels. It uses an instrumentation-grade circuit with a low-noise microphone for high-precision ...

SKU: AF-1849 | Brand: Adafruit

Get started with wearable electronics using the Adafruit Gemma Sensor Starter Pack. This all-in-one kit includes a GEMMA V2 board, sewable RGB NeoPixels, multiple sensors, a rechargeable battery with charger, and ever...

SKU: AF-2378 | Brand: Adafruit

The Arduino Pro Mini is SparkFun's minimal design approach to Arduino.  It's essentially a 5v Arduino that runs an 16 MHz bootloader on a super small, super thin board.  There are no connectors attached -...

SKU: DF-DFR0126 | Brand: DFRobot

This Audio Analyzer module features the MSGEQ7 graphic equalizer display filter.It will give your arduino ears. Sound is broken down into seven frequency bands and the peak level for each band can be read. The seven ...

SKU: PL-2463 | Brand: Pololu

The Vishay TSSP58P38 is a unique modulated IR receiver that is designed for IR brightness detection instead of data communication for remote control. This sensor can be used with a 38 kHz modulated IR emitter an...

SKU: SF-SEN-09198 | Brand: SparkFun

The Minisense 100 from Measurement Specialties is a low-cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Useful for detecting vibration and ‘tap’ inputs from a user....

SKU: SF-SEN-09197 | Brand: SparkFun

A flexible piezo vibration sensor from Measurement Specialties, commonly used for detecting flex, touch, vibration, and shock. The PVDF polymer film generates a small AC voltage (up to ±90 V) when it moves, which can ...

SKU: SF-BOB-09110 | Brand: SparkFun

This is the breakout board for the thumb joystick. Pins are broken out to a 0.1" header and includes 4 mounting holes in the corners.

SKU: AF-2771 | Brand: Adafruit

The Feather 32u4 Basic Proto is the no-frills member of the Feather 32u4 family, with a built-in prototyping area where you can solder on extra components like buttons, sensors, or connectors without needing a separat...

SKU: DF-SEN0139 | Brand: DFRobot

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage them or mishandle them. You just need an additional IC (Like an AD595) ...

SKU: SF-DEV-08777 | Brand: SparkFun

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to dig...

SKU: SF-SEN-00242 | Brand: SparkFun

The Sharp GP2Y0A21YK is an infrared proximity sensor with an analogue voltage output that varies with distance — from 3.1 V at 10 cm to 0.4 V at 80 cm. It uses an IR emitter and position-sensitive detector to measure ...

SKU: SF-SEN-11574 | Brand: SparkFun

Heart rate data can be really useful whether you’re designing an exercise routine, studying your activity or anxiety levels or just want your shirt to blink with your heart beat. The problem is that heart rate can be ...

SKU: AF-3000 | Brand: Adafruit

Would you like to learn electronics, with an all-in-one board that has sensors and LEDs built in? Circuit Playground is here - and it's the best way to practice programming on real hardware with no soldering or sew...

SKU: AF-178 | Brand: Adafruit

A 100 mm linear soft potentiometer (ribbon sensor) manufactured by Spectra Symbol. This pressure-sensitive ribbon controller features an adhesive backing for easy mounting and provides a variable resistance output bas...

SKU: AF-182 | Brand: Adafruit

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.These sensors are easy to use, they are basically resistors that change ...

SKU: AF-334 | Brand: Adafruit

If you've got a resistive touch screen that you'd like to use, you'll need this breakout! It has a fine pitch (0.5mm) connector soldered onto it and it's broken out into the 4 resistive wires of the panel. A petite...

SKU: AF-3246 | Brand: Adafruit

A neat little breakout board designed for mounting a PSP-style mini thumbstick to your project. The board features panel-mount friendly hole placement and dual-sided headers for mechanical stability when connected to ...

SKU: AF-444 | Brand: Adafruit

Add a tiny joystick to your project with this PSP thumbstick. This is a replacement component for PSP1000's, but we think they'd make for a great little joystick/thumbstick add-on for a wearable, or portable pro...