Brands and Manufacturers

SKU: AF-2479 | Brand: Adafruit

The Adafruit Bluefruit LE UART Friend adds Bluetooth Low Energy connectivity to any microcontroller or computer with a hardware or software serial port. With hardware flow control built in, you won't lose data during ...

SKU: DF-SEN0005 | Brand: DFRobot

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, aut...

SKU: DF-DFR0090 | Brand: DFRobot

An 8-digit serial LED display module that uses an SPI (3-wire) interface, requiring only three I/O pins from your Arduino or microcontroller. Multiple modules can be daisy-chained together for longer displays. The fli...

SKU: DF-SEN0233 | Brand: DFRobot

A multifunction air quality monitor that measures particulate matter (PM2.5), formaldehyde concentration, temperature, and humidity. It uses laser scattering to detect suspended particles in the air, an electrochemica...

SKU: DF-TEL0020 | Brand: DFRobot

This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. Th...

SKU: AF-2633 | Brand: Adafruit

The Adafruit Bluefruit LE SPI Friend adds Bluetooth Low Energy connectivity to any microcontroller with just 4–5 GPIO pins. Using SPI instead of UART means no baud rate configuration or flow control to worry about — c...

SKU: PL-2454 | Brand: Pololu

The QTR-L-1A reflectance sensor incorporates a right-angle infrared LED and a right-angle phototransistor in an inexpensive, tiny 0.35″ × 0.3″ module that can be mounted almost anywhere and is great for e...

SKU: SF-BOB-09322 | Brand: SparkFun

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>...

SKU: AF-466 | Brand: Adafruit

The VCNL4010 sensor is a nice way to add a small-distance proximity sensor to your microcontroller project. For longer distances (in the range of cm, you can use a SHARP IR distance sensor, but those are only good ...

SKU: DF-SEN0131 | Brand: DFRobot

INTRODUCTION This is an Arduino Propane Gas Sensor. It uses MQ6 probe to detect iso-butane, propane and liquefied petroleum gas (LPG). It is less sensitive with alcohol, cooking fumes an...

SKU: SF-COM-08348 | Brand: SparkFun

The TEMT6000x01 is a compact ambient light sensor that operates as an NPN phototransistor. The more light that hits the sensor, the stronger the base bias, producing an analog output proportional to the ambient light ...

SKU: AF-2999 | Brand: Adafruit

The Adafruit ATWINC1500 WiFi Breakout adds 802.11b/g/n WiFi connectivity to your Arduino or other microcontroller project over SPI. Built around the Microchip ATWINC1500 module, this FCC-certified breakout delivers re...

SKU: DF-FIT0319 | Brand: DFRobot

This is a photoelectric switch that is composed of emitter and receptor.The emitter consists of a laser diode,and the laser has the characteristics of high precision, good orientation etc.The receptor consists of a p...

SKU: SF-SEN-13963 | Brand: SparkFun

The SparkFun LIS3DH breakout is a low-power, three-axis accelerometer with 12-bit resolution, ideal for adding motion and orientation detection to your projects. It communicates over I2C or SPI and includes three addi...

SKU: PL-1268 | Brand: Pololu

The Pololu MinIMU-9 v2 is a compact (0.8″ × 0.5″) board that combines ST’s L3GD20 3-axis gyroscope and LSM303DLHC 3-axis accelerometer and 3-axis magnetometer to form an inertial measurement unit (IMU); we therefore r...

SKU: PL-1265 | Brand: Pololu

This board has been replaced by the newer MinIMU-9 v2 L3GD20 and LSM303DLHC carrier, which offers improved magnetic sensing resolution, a wider acceleration measurement range, and gyro measurements that are more resis...

SKU: SF-SEN-11862 | Brand: SparkFun

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-3LA, a very simple...

SKU: SF-SEN-11859 | Brand: SparkFun

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emi...

SKU: PL-1245 | Brand: Pololu

The Satellite Module 003 is an RGB LED round “pixel” with three bright surface-mount RGB LEDs. This LED module is designed to be used with the OctoBrite DEFILIPPI to easily integrate full-color LED lighting into your...

SKU: AF-3060 | Brand: Adafruit

The Adafruit ATWINC1500 WiFi Breakout with uFL Connector adds 802.11b/g/n WiFi connectivity to your Arduino or other microcontroller project over SPI. This version features a uFL antenna connector instead of an onboar...