Audio

SKU: DF-SEN0487 | Brand: DFRobot

This tiny MEMS microphone has an amplifier gain of 66. When there is no sound detected, it outputs voltage around 0.66*VCC. When speaking, you can easily get the acoustic waveform by ADC sampling. The module can be us...

SKU: DF-DFR0308 | Brand: DFRobot

The Arduino DTMF Shield is a dual-tone multi-frequency decoder module that lets your Arduino interpret touch-tone signals from phones. Connect it to a GSM/GPRS shield and you can send commands to your Arduino via phon...

SKU: LB-LS6069 | Brand: Little Bird

This compact enclosed speaker delivers clear audio output at up to 6W with a 4Ω impedance, suitable for a wide range of DIY audio and display projects. It comes with a JST PH 2-pin input cable for easy connection to a...

SKU: SF-WIG-18159 | Brand: SparkFun

The Tsunami Super WAV Trigger is a polyphonic audio player built around an ARM Cortex M7, capable of mixing up to 32 mono or 18 stereo simultaneous uncompressed 44.1 kHz, 16-bit WAV tracks. Each track can be independe...

SKU: SF-COM-15350 | Brand: SparkFun

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind you might find in o...

SKU: DF-SEN0232 | Brand: DFRobot

The Gravity Analog Sound Level Meter is an Arduino-compatible decibel meter that accurately measures environmental noise levels. It uses an instrumentation-grade circuit with a low-noise microphone for high-precision ...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: SF-COM-27247 | Brand: SparkFun

A compact through-hole speaker that solders directly to your PCB. When you need better audio quality than a piezo buzzer but don't have room for a full-sized speaker, this 30mm unit hits the sweet spot – clear enough ...

SKU: AF-5769 | Brand: Adafruit

The Adafruit Audio BFF is a compact add-on board that turns your QT Py or Xiao into a powerful audio playback device. It features a microSD card slot (up to 64 GB) and a MAX98357 I2S 3W amplifier, all designed to fit ...

SKU: AF-4361 | Brand: Adafruit

Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jac...

SKU: KI-46124 | Brand: Kitronik

The MonkMakes Speaker Board is a compact, amplified speaker designed for the BBC micro:bit. Simply connect it with crocodile clips and start adding sound to your micro:bit projects — despite its small size, the speake...

SKU: SF-BOB-11044 | Brand: SparkFun

This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it won’t shake a stadium, ...

SKU: SF-WIG-25860 | Brand: SparkFun

This compact audio trigger board is a high-fidelity polyphonic WAV player for interactive installations, instruments, exhibits and embedded sound projects. It plays uncompressed 16-bit, 44.1kHz mono and stereo WAV fil...

SKU: AF-6049 | Brand: Adafruit

Add digital audio input to a capable microcontroller or single-board computer with this tiny breakout for the TDK ICS43434 I2S MEMS microphone. MEMS microphones detect sound like classic electret mics, but are much sm...