Audio

SKU: DF-DFR0299 | Brand: DFRobot

Sing for the moment! The DFPlayer Mini is a small and low cost MP3 module player with an simplified output directly to the speaker. The module can be used as a stand alone module with attached battery, speake...

SKU: AF-1713 | Brand: Adafruit

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use th...

SKU: AF-1739 | Brand: Adafruit

This large enclosed piezo element (30 mm diameter) converts vibration to voltage and voltage to vibration, making it useful both as a buzzer for generating tones and as a sensor for detecting knocks and impacts. The e...

SKU: AF-1063 | Brand: Adafruit

A well-designed electret microphone amplifier breakout built around the Maxim MAX4466 op-amp, specifically engineered for microphone amplification with excellent power supply noise rejection. The board comes fully ass...

SKU: AF-3923 | Brand: Adafruit

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires w...

SKU: SF-SEN-14262 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy-to-use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of sound...

SKU: DF-DFR0034 | Brand: DFRobot

This is a new Arduino compatible Analog Sound Sensor. Sound Sensor is typically used in detecting the loudness in ambient, the Arduino can collect its output signal and actuate accordingly. You may use it to make some...

SKU: DF-DFR0064 | Brand: DFRobot

The DFRobot 386AMP audio amplifier module is based on the LM386 low-voltage audio power amplifier IC. With a fixed voltage gain of 26 dB (20× amplification) and static power consumption of only 24 mW at 6V, it's well ...

SKU: DF-SEN0487 | Brand: DFRobot

This tiny MEMS microphone has an amplifier gain of 66. When there is no sound detected, it outputs voltage around 0.66*VCC. When speaking, you can easily get the acoustic waveform by ADC sampling. The module can be us...

SKU: DF-DFR0308 | Brand: DFRobot

The Arduino DTMF Shield is a dual-tone multi-frequency decoder module that lets your Arduino interpret touch-tone signals from phones. Connect it to a GSM/GPRS shield and you can send commands to your Arduino via phon...

SKU: DF-SEN0232 | Brand: DFRobot

The Gravity Analog Sound Level Meter is an Arduino-compatible decibel meter that accurately measures environmental noise levels. It uses an instrumentation-grade circuit with a low-noise microphone for high-precision ...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: AF-4361 | Brand: Adafruit

Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jac...

SKU: KI-46124 | Brand: Kitronik

The MonkMakes Speaker Board is a compact, amplified speaker designed for the BBC micro:bit. Simply connect it with crocodile clips and start adding sound to your micro:bit projects — despite its small size, the speake...

SKU: SF-BOB-11044 | Brand: SparkFun

This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it won’t shake a stadium, ...

SKU: SF-WIG-25860 | Brand: SparkFun

This compact audio trigger board is a high-fidelity polyphonic WAV player for interactive installations, instruments, exhibits and embedded sound projects. It plays uncompressed 16-bit, 44.1kHz mono and stereo WAV fil...