Arduino Shields

SKU: SF-COM-11041 | Brand: SparkFun

A bare PCB for building a relay control circuit, based on SparkFun's Controllable Power Outlet tutorial. It allows you to switch high-voltage loads using a simple 0–5V GPIO signal from any microcontroller. Components ...

SKU: SS-ELB141D1P | Brand: Seeed Studio

This is a Protoshield kit with the same connector as Electronic Brick, you can solder something onto this and use it as a regular Electronic Brick.    You will also need this cable to connect it to Se...

SKU: AF-1750 | Brand: Adafruit

The Synthetos gShield (formerly grblShield) V5 is a 3-axis CNC stepper motor driver shield for Arduino. Designed as a complete hardware companion for the grbl CNC motion control firmware, it turns an Arduino Uno into ...

SKU: AF-2024 | Brand: Adafruit

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — att...

SKU: PL-2508 | Brand: Pololu

This shield makes it easy to build an Arduino-controlled Zumo robot. The shield mounts onto an assembled Zumo chassis, connecting directly to the chassis’s battery terminals and motors, and the Arduino plugs into ...

SKU: DF-DFR0117 | Brand: DFRobot

Arduino has a small amount of data storage space, The Arduino UNO has 32k. It doesn't have enough space if you want to store a lot of data. Therefore, we need to add an EEPROM Data Storage Module to increase its stora...

SKU: AF-2653 | Brand: Adafruit

Get your Particle (formally known as Spark) Photon moving with a PhoBot Robotics shield. No, this is not a robot that makes you a delicious bowl of Vietnamese soup.  Instead, it's a board from Simon Monk ...

SKU: DF-DFR0174 | Brand: DFRobot

The XBee USB Adapter V2 is an update version from DFRobot. It features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The Atmega8U2 firmware uses the standard USB ...

SKU: SF-DEV-14285 | Brand: SparkFun

The SparkFun Wireless Motor Driver Shield is designed to make connecting motors, sensors and other components to your Arduino-based project as fast and easy as possible. The heart of the Wireless Motor Driver Shield i...

SKU: SF-KIT-14180 | Brand: SparkFun

Robots are fun, and Arduinos are easy. So wouldn’t it be nice if there were a kit that included everything you need to get your Arduino device set up to control a simple two-motor-circuit buddy? The SparkFun Ardumoto ...

SKU: SF-DEV-14129 | Brand: SparkFun

The Ardumoto Shield is a dual-motor controller for Arduino based on the L298 H-bridge. It can drive two DC motors at up to 2A per channel, making it an excellent platform for RC vehicles and small autonomous robots. ...

SKU: DF-DFR0256 | Brand: DFRobot

The Mega Multi IO Expansion Shield lets you stack up to four shields simultaneously on an Arduino Mega or Due without worrying about I/O pin conflicts. All Mega I/O pins are expanded and routed to four separate shield...

SKU: DF-DFR0274 | Brand: DFRobot

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED stri...

SKU: DF-DFR0008 | Brand: DFRobot

The upgraded Arduino Input Shield includes a two axis mini joystick (with moment switch) as well as four colored push buttons(Red,Yellow,Blue,Green). The reserved APC220 Radio Data Module(SKU:TEL0005) interface...

SKU: SF-DEV-13770 | Brand: SparkFun

The Intel® Edison is an ultra-small computing platform that will change the way you look at embedded electronics. Each Edison is packed with a huge amount of tech goodies into a tiny package while still providing t...

SKU: AF-171 | Brand: Adafruit

Make your own Arduino motor party with a motor shield and a fine assortment of motors! New! we've upgraded the shield to our new version 2, with more powerful drivers, and uses fewer pins to boot! Included in this ...

SKU: DF-DFR0285 | Brand: DFRobot

The Beetle shield is designed to attach a Beetle (DFR0282) controller for easy connecting servos and sensors. ​ SPECIFICATIONS Operating voltage: 3 - 5V Compatible with DFRobot Beetle ...

SKU: SF-DEV-13210 | Brand: SparkFun

This is the RGB/Button Shield for RFduino, a small add-on board for the RFduino DIP module. Just as its name suggests, this little board is equipped with two pushbuttons and an RGB LED. This shield can be easily at...

SKU: AF-462 | Brand: Adafruit

Turn any Arduino into an AVR chip programmer with this shield kit. Designed for burning Arduino bootloaders onto blank ATmega328P chips, it can also be configured as a standalone AVR ISP programmer that works without ...

SKU: SF-DEV-10618 | Brand: SparkFun

The SparkFun Power Driver Shield Kit lets you switch high-current loads directly from your Arduino using six RFP30N06LE N-channel MOSFETs. Connect a computer power supply or other DC source to drive motors, solenoids,...