All Products

SKU: AF-3006 | Brand: Adafruit

The Adafruit MAX98357A I2S Class D Amplifier Breakout is an all-in-one digital audio solution that decodes I2S audio and amplifies it directly to a speaker — no separate DAC required. Delivering up to 3.2W into a 4Ω s...

SKU: AF-5346 | Brand: Adafruit

The Adafruit MCP23017 I2C GPIO Expander Breakout adds 16 extra GPIO pins to any microcontroller or microcomputer over I2C. Each pin can be configured as a digital output (driving up to 25 mA — perfect for LEDs) or as ...

SKU: AF-2167 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to tha...

SKU: AF-158 | Brand: Adafruit

Hall effect sensors detect whether a magnet is near. Useful for non-contact/waterproof type switches, position sensors, rotary/shaft encoders. I tried dozens of different hall effect sensors to see which one wou...

SKU: AF-757 | Brand: Adafruit

This bi-directional logic level converter from Adafruit uses 4× BSS138 FETs with 10K pull-up resistors to safely shift signals between different voltage levels. Unlike many level shifters, this design is fully compati...

SKU: AF-5708 | Brand: Adafruit

The Adafruit CAN Pal is a CAN bus transceiver breakout for microcontrollers that have a native CAN peripheral. It converts 3.3V logic-level CAN TX/RX signals to the differential signalling required for the CAN bus. Th...

SKU: AF-189 | Brand: Adafruit

PIR sensors are used to detect motion from pets/humanoids from about 20 feet away (possibly works on zombies, not guaranteed). This one has an adjustable delay before firing (approx 2-4 seconds), adjustable sensiti...

SKU: AF-5221 | Brand: Adafruit

This breakout PCB converts the ANO rotary navigation encoder's non-standard pinout into a straightforward, breadboard-friendly header strip. The ANO encoder combines a rotary encoder with directional and centre-push b...

SKU: AF-5578 | Brand: Adafruit

The BS612 is a compact, fully configurable mini PIR motion sensor that detects movement from approximately 3–8 metres away with a 120° detection spread. Its small form factor makes it ideal for unobtrusive motion-sens...

SKU: AF-157 | Brand: Adafruit

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to...

SKU: AF-5990 | Brand: Adafruit

The Adafruit Infrared IR Remote Transceiver combines a high-powered IR transmitter and a sensitive 38 kHz IR receiver on a single board. With two 940 nm IR LEDs (one vertical, one horizontal) driven by an onboard N-ch...

SKU: AF-2168 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that s...

SKU: AF-2264 | Brand: Adafruit

The Adafruit FT232H Breakout turns your computer into a versatile interface for hardware protocols. Using the FTDI FT232H chip with its multi-protocol synchronous serial engine, you can communicate directly with I2C, ...

SKU: AF-5423 | Brand: Adafruit

The Adafruit TSC2007 is an I2C resistive touch screen controller that offloads touch reading from your microcontroller. Instead of using multiple analog pins and constant polling, the TSC2007 handles all the touch sen...

SKU: AF-4666 | Brand: Adafruit

A compact passive infrared (PIR) motion sensor that detects movement from approximately 3–8 metres away. Much smaller than standard PIR modules, making it ideal for unobtrusive, space-constrained projects. Fully self-...

SKU: AF-5963 | Brand: Adafruit

The Adafruit 555 PWM Output STEMMA is a fully assembled 555 timer board that generates an adjustable square-wave PWM signal — no breadboard wiring or external components needed. An onboard trimmer pot lets you tune th...

SKU: AF-5913 | Brand: Adafruit

The Adafruit STEMMA Reflective Photo Interrupt Sensor uses a TCRT1000 right-angle optical module to detect reflective surfaces. An onboard IR LED emits light, and when an object reflects it back to the IR phototransis...

SKU: AF-1551 | Brand: Adafruit

You're too cool for I2C, and SPI has so many wires, 8-bit parallel... how can that be fashionable!? You are a 1-Wire kinda gal, and you want more 1-Wire breakouts in your life to complement all of your great engineeri...

SKU: AF-2926 | Brand: Adafruit

The Terminal Block Breakout FeatherWing kit is like the Golden Eagle of prototyping FeatherWings (eg. majestic, powerful, good-looking). To start, you get a nice prototyping area underneath your Feather, wi...

SKU: AF-4984 | Brand: Adafruit

The Adafruit DVI Breakout Board provides an HDMI-compatible connector with 220 Ω series resistors for generating DVI video output from microcontrollers. Designed as a source-only device, it lets you drive HDMI monitor...