All Products

SKU: AF-4446

The Adafruit eInk Feather Friend is a FeatherWing-format driver board for eInk/e-paper displays with a standard 24-pin FPC connector. It includes all the power supply circuitry and level shifting needed to connect your favourite display (up to tri-colour 4.2") to any Feather board via SPI, plus a...

SKU: AF-3176

The Feather M0 RFM69HCW Packet Radio (868/915 MHz) combines the ATSAMD21G18 ARM Cortex M0+ processor with an SX1231-based RFM69HCW radio transceiver for wireless data communication at 868 or 915 MHz. The exact radio frequency is software-configurable, allowing you to tune dynamically for your reg...

SKU: AF-2267

The Bluefruit LE Friend is your new BLE BFF! This USB-to-BLE board makes it easy to get your computer talking to your BLE enabled phone or tablet using a standard serial/UART connection. In it's simplest form, it works on the same principle as a common USB/Serial adapter (the FTDI Friend,...

SKU: AF-4372

This laser-cut acrylic enclosure kit turns your 8×8 NeoTrellis setup (four 4×4 NeoTrellis boards) into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside four NeoTrellis RGB Dr...

SKU: AF-3179

The Feather M0 RFM96 LoRa Radio (433 MHz) combines the ATSAMD21G18 ARM Cortex M0+ processor with an SX1276-based LoRa radio transceiver for long-range wireless communication at 433 MHz. LoRa modulation delivers significantly greater range than conventional packet radio — over 2 km line-of-sight w...

SKU: AF-4565

The Adafruit LSM6DSOX + LIS3MDL FeatherWing is a precision 9 Degree of Freedom (9-DoF) IMU add-on for any Feather board. It combines the LSM6DSOX accelerometer/gyroscope — known for its exceptionally low gyro drift and noise — with the LIS3MDL magnetometer for complete orientation and heading sen...

SKU: AF-3651

The Adafruit TFT FeatherWing is a 3.5" colour display with a 480×320 resolution, bright 6-LED white backlight, and a built-in resistive touchscreen. It plugs directly into any Adafruit Feather board, giving you a high-resolution colour display with touch input and a microSD card slot for image st...

SKU: AF-4145

The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay ...

SKU: AF-5255

The Adafruit LED Glasses Starter Kit includes everything you need to build a complete pair of programmable LED glasses. Pair the 116-LED front panel with the Bluetooth-enabled nRF52840 driver board, snap them onto the included fashion frames, and you're ready to create dazzling wearable light dis...

SKU: AF-5709

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps over a two-wire differential bus. Only an SPI port and two pins (chip-select and ...

SKU: AF-3177

The Feather M0 RFM69HCW Packet Radio (433 MHz) combines the ATSAMD21G18 ARM Cortex M0+ processor with an SX1231-based RFM69HCW radio transceiver for wireless data communication at 433 MHz. It includes built-in USB, LiPo battery charging, and the full Feather M0 pin set in a compact, portable form...

SKU: AF-6313 · MPN: ADA6313

Add a crisp monochrome display and simple user controls to your Feather project with this fully assembled FeatherWing. It combines a 128x64 white OLED screen with three user buttons labelled A, B and C, plus a reset button, so you can build compact menus, status displays, and handheld interfaces ...