All Products

SKU: DF-DFR1136 · MPN: DFR1136

This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....

SKU: SF-SEN-18020

The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has...

SKU: AF-973

A 50 cm (19.5″) servo extension cable for extending the reach of standard 3-pin servo connections. It features a shrouded male connector on one end and a female connector on the other, with red/black/white colour coding maintained throughout. Specifications Connector – 3-pin servo (male to fem...

SKU: DF-FIT0033

A 300 mm (11.8″) servo extension cable for when your servo needs to reach further than its built-in lead allows. Male connector on one end plugs into your controller, female connector mates with the servo. Also works as a simple 0.1″ pitch jumper cable. Specifications Length – 300 mm (11.8″) ...

SKU: AF-5855

A compact 5 V, 0.3 W solar panel from Voltaic Systems, built with ETFE (Ethylene Tetrafluoroethylene) construction for superior durability over standard PET or laminate panels. Featuring 10 high-efficiency monocrystalline SunPower cells with 22%+ efficiency, this panel is waterproof, scratch-resi...

SKU: DF-FIT0335

This 500 mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors, which means it is compatible with almost all of the RC servos.The connectors have gold-flashed cont...

SKU: SF-GPS-15005 · MPN: GPS-15005

Built around the u-blox NEO-M8P-2, this breakout brings high-accuracy GNSS and GPS positioning with RTK support to the Qwiic ecosystem. It’s designed for applications where standard GPS accuracy isn’t enough, with RTK positioning down to 25mm so you can track the location of a device, robot or ve...

SKU: AF-4055

This snap-in panel mount USB A extension cable lets you run a USB port through an enclosure wall without screws or drilling mounting holes. Cut a rectangular opening in your panel, snap the connector in, and the integrated bezel covers any rough edges for a clean finish. Both ends are standard U...

SKU: AF-3848

An isolated Power over Ethernet (PoE) module that extracts power from the Ethernet cable's centre taps and outputs a regulated 5 V at up to 1.8 A. The built-in isolation transformer ensures there is no direct electrical connection between the Ethernet side and the 5 V output — important for safet...

SKU: DF-FIT0334

This 300mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors, which means it is compatible with almost all of the RC servos.The connectors have gold-flashed conta...

SKU: AF-4702

The Adafruit RGB Matrix FeatherWing Kit for nRF52840 lets you drive HUB75-type RGB LED matrices from nRF52840-based Feather boards. With built-in power regulation and a compact form factor, it's the easiest way to create colourful scrolling displays and LED wall projects using the Feather ecosyst...

SKU: AF-4823

A 150mm (6″) GPIO extension cable for Raspberry Pi models with a 2×20 pin header. Extends all 40 GPIO pins between your Pi and a HAT, Bonnet, pHAT, or other accessory, allowing you to mount add-ons away from the board. Plug the socket end onto the Raspberry Pi's GPIO header (white mark aligned w...