All Products

SKU: LB-LR0064

The KnockOffDuino® Uno is functionally the same as the Arduino Uno R3 at a fraction of the cost. It is the Arduino for beginners and 100% Uno compatible, however it uses the CH340G usb to serial chip instead of the 16u2/8u2 found in the official Arduino Uno R2/R3 so instead of the Arduino Uno ...

SKU: SF-DEV-11224

This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf fil...

SKU: LB-00300

The Little Bird Uno R3, is a 100% Arduino™ compatible development board.Just like the original Arduino Uno the Arduino Shield compatible design makes adding expansion boards easy.This Arduino can be powered from 7-12 VDC or using your computer's USB port (limited available current to pins if don...

SKU: AF-1551 · MPN: 1551

You're too cool for I2C, and SPI has so many wires, 8-bit parallel... how can that be fashionable!? You are a 1-Wire kinda gal, and you want more 1-Wire breakouts in your life to complement all of your great engineering. Well rock on, because here you go, it's a 1-Wire controller with two open-dr...

SKU: DF-DFR0274

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED strip. A built-in IR receiver enables remote control operation, and an on-board fuse...

SKU: EC-ACA30002A

The Component Kit for Arduino E3 is a starter-friendly assortment of essential electronic components for use with any Arduino-compatible board. It includes a broad range of resistor values, LEDs in four colours, tactile switches with button caps, potentiometers, and pin headers — everything you n...

SKU: EC-ACS26020S

Did you know your Arduino can burn bootloaders onto Atmega chips, turning them into Arduino compatible microcontrollers? It required a breadboard and a whole mess of jumper wires but we've just made it a ton easier on you with the AVR ISP Shield!It is very easy to use. Just following the Arduino ...

SKU: DF-DRI0017

The DFRobot 2×2A Motor Shield uses the L298P dual full-bridge driver chip to control two 4.8–35 V DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 10 and 11 for speed control and digital pins 12 and 13 for enable/disable. The shield ...

SKU: AF-2439 · MPN: 2439

An analog LED strip featuring both RGB and warm white (~3000K) LEDs at 60 LEDs per metre on a weatherproof white flexi PCB. Control the entire strip at once using any microcontroller and four transistors (one per channel) — no addressable LED library needed, just PWM for colour mixing. Power the...

SKU: EC-AS402812NP

This is the NeoPixel Shield from Duinofun. This Arduino shield is equipped with 40 WS2812 RGB LEDs arranged in an 5x8 matrix with on one pin (Digital #6) needed to control them all.Each shield is powered by the 5V onboard Arduino supply and as long as you aren’t lighting up all the LEDs full powe...

SKU: AF-6478 · MPN: ADA6478

This compact breakout combines the STCC4 CO2 sensor with a Sensirion SHT41 temperature and humidity sensor for convenient indoor air monitoring. The STCC4 measures true CO2 using a thermal conductivity method rather than estimating from VOCs, and the onboard SHT41 helps improve the CO2 measuremen...

SKU: LB-LS7756

Packing list: 10 × White LEDs10 × Yellow LEDs10 × Blue LEDs10 × Green LEDs10 × Red LEDs1 × RGB LED2 × Photoresistors (LDR)1 × Thermistor5 × Rectifier Diodes (1N4007)5 × NPN Transistors (PN2222)1 × Optocoupler IC (4N35)1 × Shift Register IC (74HC595)10 × Tactile Push Buttons (small)1 × Active...

SKU: SF-PRT-11417

These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin, 1 10-pin and 1 6-pin), enough to connect a shield t...

SKU: AF-714 · MPN: 714

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs we stock in the shop both the RGB negative and RGB positive. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 3 to control the RGB backlight for a...

SKU: SF-DEV-13975

At SparkFun we use many Arduinos and we’re always looking for the simplest, most stable one. Each board is a bit different and no one board has everything we want, so we decided to make our own version that combines all our favorite features. The SparkFun RedBoard combines the simplicity of the U...

SKU: EC-AS00121CTH

This Capacitive Touch Shield has 9 build-on capacitive touchpads, and the other 3 electrodes for further usage. With this shield, you can have a total of 12 touch-sensitive buttons. This Shield uses the MPR121 which is a great way to build simple capacitive touch interfaces using the I2C communic...

SKU: DF-DFR1085 · MPN: DFR1085

##Introduction The new Arduino UNO R4 comes in two versions: the UNO R4 WiFi and the UNO R4 Minima. It runs on the Renesas RA4M1 (Arm Cortex®-M4) processor, with a clock speed of 48MHz, which provides a 3x increase over the UNO R3. In addition to that, the SRAM has been upgraded from 2kB to 32kB ...

SKU: DF-DRI0009

The DFRobot 2×2A DC Motor Shield uses the L298P dual full-bridge driver chip to control two DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 5 and 6 for speed control and digital pins 4 and 7 for enable/disable. The shield can be pow...