All Products

SKU: AF-3653

Add WiFi connectivity to your Arduino-compatible board with the Adafruit WINC1500 WiFi Shield, featuring the FCC-certified ATWINC1500 module from Atmel. This 802.11b/g/n shield supports WEP, WPA, and WPA2 encryption with TLS 1.2 for secure connections, and communicates over SPI at speeds up to 12...

SKU: AF-3654

Add WiFi connectivity to your Arduino-compatible board with the Adafruit WINC1500 WiFi Shield, featuring the FCC-certified ATWINC1500 module from Atmel. This 802.11b/g/n shield supports WEP, WPA, and WPA2 encryption with TLS 1.2 for secure connections, and communicates over SPI at speeds up to 12...

SKU: AF-2999

The Adafruit ATWINC1500 WiFi Breakout adds 802.11b/g/n WiFi connectivity to your Arduino or other microcontroller project over SPI. Built around the Microchip ATWINC1500 module, this FCC-certified breakout delivers reliable wireless networking with TLS 1.2 support for secure connections. With bu...

SKU: AF-3060

The Adafruit ATWINC1500 WiFi Breakout with uFL Connector adds 802.11b/g/n WiFi connectivity to your Arduino or other microcontroller project over SPI. This version features a uFL antenna connector instead of an onboard antenna, allowing you to use an external antenna for improved range or placeme...

SKU: EC-ACS17101S

This WiFi Shield connects your Arduino or Crowduino to the internet wirelessly. Just connect it to your wireless network with a few simple instructions, you can start to control your applications through the internet now. This Wifi Shield utilizes a RN171 which is a complete, standalone TCP/IP wi...

SKU: AF-5889 · MPN: ADA5889

This compact wireless development board gives you a full-featured ESP32 platform in the familiar ItsyBitsy format. It uses the ESP32 PICO ECO V3 in an FCC-certified ESP32 Pico module, combining a dual-core 240MHz processor with 2.4GHz Wi-Fi, Bluetooth® Classic and BLE, plus 8 MB of Flash and 2 MB...

SKU: AF-2598

The Adafruit Feather M0 WiFi combines an ATSAMD21G18 ARM Cortex M0+ processor with an ATWINC1500 WiFi module for an all-in-one Arduino-compatible development board with built-in USB, battery charging, and 802.11b/g/n connectivity. This version comes fully assembled with headers soldered. The FCC...

SKU: AF-945

A 200 mm (8″) swivel dipole antenna with 5 dBi gain and an RP-SMA connector — the industry-standard fitting found on most WiFi routers and wireless modules. The higher gain compared to the 2 dBi version extends range at the cost of a larger form factor. The swivel joint lets you angle the antenna...

SKU: SF-WRL-00144

A tiny 2.4 GHz ceramic chip antenna designed for surface-mount PCB layouts. While it won't match the range of a full-size rubber duck antenna, its extremely compact footprint lets you add wireless capability to space-constrained designs. Works well with Nordic Semiconductor ICs and other 2.4 GHz ...

SKU: DF-DFR0896

The ESP32-S3-WROOM-1-N4 is a powerful Wi-Fi and Bluetooth LE MCU module built around the ESP32-S3 SoC. Featuring a dual-core Xtensa LX7 processor running at up to 240MHz, 4MB SPI flash, and hardware acceleration for neural network computing, it's designed for AIoT applications including wake word...

SKU: AF-944

A 100 mm (4″) swivel dipole antenna with 2 dBi gain and an RP-SMA connector — the industry-standard fitting found on most WiFi routers and wireless modules. The swivel joint lets you angle the antenna for optimal signal direction. Key Features 2 dBi Gain – Omni-directional coverage for short-t...

SKU: SF-GPS-26916 · MPN: GPS-26916

This compact high-precision positioning board combines a Quectel LG290P GNSS RTK receiver with an Espressif ESP32-PICO-MINI-02 MCU module. It runs SparkFun’s RTK Everywhere firmware, letting it operate as a base station or rover for precision navigation projects.The ESP32 adds WiFi, Bluetooth® an...

SKU: SF-WRL-19899

The ESP32-WROOM-DA, which is a module that achieves high-quality, wireless connectivity across large areas, using two complementary PCB antennas in different directions. Also, based on its industry-leading technical specifications, the co-existence of WiFi and Bluetooth® (Classic & Low-Energy)...

SKU: EC-WAW24031A

A 2.4 GHz WiFi antenna with 3 dBi gain, suitable for DIY wireless projects. It provides improved range over built-in PCB antennas on WiFi-enabled microcontrollers and development boards. Key Features 3.0 ± 0.7 dBi Gain – Improved signal strength over stock antennas 2400–2500 MHz Frequency Ran...

SKU: AF-2308

A 100 mm (4″) flexible WiFi antenna with approximately 4 dBi gain and a U.FL (IPEX) connector. The flexible design lets you bend and position the antenna to suit your enclosure or project layout, while the U.FL connector snaps directly onto boards without the need for an adapter. Key Features ...

SKU: EC-WAW24040A

A 2.4 GHz WiFi antenna with 4 dBi gain and an IPEX (MHF) connector, enclosed in a protective cover. It connects directly to boards with an IPEX/U.FL socket, providing improved wireless range over built-in PCB antennas. Key Features 4 dBi Gain – Higher gain than standard stub antennas for exten...

SKU: AF-1012

Make your Internet of Things device cable-free by adding WiFi. Take advantage of the Raspberry Pi and Beagle Bone's USB port to add a low cost, but high-reliability wireless link. We tried half a dozen modules to find one that works well with the Pi and Bone without the need of recompiling any...

SKU: LB-LR0214-102A

The ESP-12E is an enhanced version of the popular ESP8266 WiFi module, offering improved impedance matching, better signal output, and stronger anti-jamming performance. It provides a complete WiFi networking solution via a simple serial (UART) interface, making it easy to add WiFi to any microco...

SKU: AF-5344

ESP32-WROOM-DA (the DA is for Dual Antenna) is a powerful Wi-Fi + Bluetooth Classic + Bluetooth LE MCU module, with two complementary PCB antennas in different directions. Packed with 8 MB of internal QSPI Flash, it has lots of memory and great WiFi connectivity no matter where or how it is inst...

SKU: LB-LR0214-80A

ESP-12F: breakthrough design, there are new breakthroughs. The new four-layer board design, the new revision antenna RF performance optimisation, compared to the communication from the ESP-12E increased by 30% to 50%! Semi-hole chip technology, the whole IO leads, with metal shielding shell, has ...