All Products

SKU: AF-715

The Adafruit I²C Controlled + Keypad Shield Kit lets you drive a 16×2 character LCD and read 5 navigation buttons using only two I²C pins on your Arduino. This frees up the 9+ digital pins that a standard LCD connection would require, while still allowing other I²C devices to share the bus. The ...

SKU: SF-DEV-13298

The Touch Board from Bare Conductive is an easy-to-use Arduino@Heart board that gives you the ability to turn almost any material or surface into a sensor. Each Touch Board offers 12 electrodes for your a conductive ink or other type of connector that can be drawn or attached to create light s...

SKU: DF-DFR0260

The Arduino DMX Shield is a low-cost, high-quality interface that connects your Arduino to DMX512 lighting networks. Built around the MAX485 transceiver and equipped with NEUTRIK XLR 3-pin connectors (one male, one female), it can operate as a DMX Master, Slave, or RDM transponder. Each shield re...

SKU: TB-XC4454

This Arduino-compatible LCD shield combines a 16×2 character LCD display with a six-button keypad on a single board. The backlit display and built-in navigation buttons (up, down, left, right, select, and reset) make it easy to create user-friendly menus and interfaces for your Arduino projects. ...

SKU: AF-815

The Adafruit 16-Channel PWM/Servo Driver uses the PCA9685 chip to provide 16 channels of 12-bit PWM output over I2C. With a built-in clock, the driver runs independently — no need to continuously send signals from your microcontroller. Ideal for controlling servos, LEDs, or any PWM-driven device....

SKU: AF-802

The Adafruit 1.8" Colour TFT Shield is a plug-and-play display solution for Arduino, combining a bright 128×160 pixel TFT screen with a microSD card slot, 5-way joystick navigation switch, and three tactile buttons. This R3-format shield works with any Arduino or Metro board including the Metro M...

SKU: SF-DEV-12761

The SparkFun microSD Shield gives your Arduino mass-storage capability via a microSD card slot, making it ideal for data-logging and projects that need to read or write files. Communication with the microSD card uses the SPI interface. The SCK, DI, and DO pins connect to the ATmega168/328's stan...

SKU: DF-DFR0023

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a functional range between 0 degree Celsius to 100 degree Celsius with a sensitivity ...

SKU: DF-SEN0133

This is an Arduino hydrogen gas sensor. It has high sensitivity to Hydrogen (H2) and less sensitivity to alcohol, LPG,cooking fumes . Hydrogen gas is highly flammable and will burn in air at a very wide range of concentrations The sensitivity is able to be adjusted by the potentiome...

SKU: DF-SEN0129

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smoke. The sensitivity can be adjusted by the potentiometer. The output is ...

SKU: DF-SEN0131

INTRODUCTION This is an Arduino Propane Gas Sensor. It uses MQ6 probe to detect iso-butane, propane and liquefied petroleum gas (LPG). It is less sensitive with alcohol, cooking fumes and cigarette smoke. It can be used in gas leakage detecting equipment in...

SKU: SF-DEV-21247

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, digital cameras, Bluetooth dongles, game controllers, and more. This version up...

SKU: DF-DFR1032

The Arduino Portenta H7 Lite is a high-performance dual-core development board and the cost-optimised entry point in the Portenta H7 series. It uses the same STM32H747XI MCU as the full Portenta H7, featuring a Cortex-M7 core (up to 480MHz) and a Cortex-M4 core for parallel multi-threaded process...

SKU: DF-SEN0127

  INTRODUCTION This is a generic Arduino gas sensor. It has MQ2 probe which is able to detect LPG, i-butane, propane, methane ,alcohol, Hydrogen, smoke.It can be used in gas leakage detecting device in consumer and industry markets. It has a high sensitivity and fast response time. ...

SKU: DF-SEN0132

INTRODUCTION This is an Arduino Carbon Monoxide Sensor. It uses MQ7 probe to detect Carbon Monoxide (CO) concentrations in the air from 20 to 2000ppm. The sensitivity can be adjusted by the potentiometer. The output is proportional to the density o...

SKU: SS-101020003

A simple momentary push button module in the Grove form factor. When pressed it outputs a HIGH signal; when released it returns to LOW. The button includes a built-in pull-down resistor, so it's ready to use as a digital input straight out of the box. Part of the Seeed Studio Grove ecosystem, it...

SKU: DF-KIT0018

The DFRobot Gravity Intermediate Kit for Arduino takes you beyond the basics with a comprehensive set of sensors, modules, and an Arduino-compatible board. Starting with simple LED projects and progressing to more complex builds like a mini electronic drum kit, sound-activated LED, and digital di...

SKU: TB-XC4392

The Arduino Compatible Long Range LoRa Shield turns your Arduino into a LoRa wireless node capable of transmitting and receiving data over several kilometres — without the need for a GSM network. Built around the Semtech SX1276 transceiver on the 915MHz band (Australian-legal), it's ideal for rem...

SKU: DF-DFR0600

PYNQ-Z2 is a FPGA development board based on ZYNQ  XC7Z020 FPGA, intensively designed to support PYNQ, a new open-sources framework that enables embedded programmers to explore the possibilities of xilinx ZYNQ SoCs without having to design programming logic circuits. Benefiting from progr...

SKU: AF-1411

The Adafruit 16-Channel PWM/Servo Shield brings PCA9685-based servo and PWM control to any Arduino in a convenient shield format. Using only I2C (SCL and SDA), the shield provides 16 channels of 12-bit PWM output with a built-in clock — no continuous signal from your microcontroller needed. Up t...