Batteries (LiPo, NiMH, coin cell)

SKU: AF-1868 | Brand: Adafruit

A simple breakout board with a CR1220 coin cell battery holder pre-soldered and broken out to 0.1″ pitch pins. Ideal for powering very low-current projects or providing battery backup for a real-time clock (RTC) modul...

SKU: AF-1870 | Brand: Adafruit

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit ...

SKU: AF-248 | Brand: Adafruit

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells f...

SKU: AF-3286 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making i...

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: SF-PRT-10592 | Brand: SparkFun

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the batte...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: SF-PRT-10255 | Brand: SparkFun

The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a LiPo battery, has solder jumper selectable 5V and 3.3V output, and an under voltage protection...

SKU: SF-PRT-10217 | Brand: SparkFun

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells ...

SKU: AF-770 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: AF-2089 | Brand: Adafruit

A snap-in battery holder for Sony NP-F series camcorder batteries, with a pre-attached 2.1 mm DC barrel plug for powering 7 V DC devices. Clip in a compatible Li-Ion battery pack and connect directly to robots, Arduin...

SKU: AF-5580 | Brand: Adafruit

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing rema...

SKU: TB-SB2933 | Brand: Little Bird

This range of Panasonic eneloop batteries have numerous advantages over regular rechargeables. Key characteristics include low self-discharge, they are pre-charged so can be used right out of the packet, and can be re...

SKU: TB-MB3563 | Brand: Little Bird

Keep your Eneloop and other Ni-MH batteries charged and ready to go with this lightweight Panasonic charger. It charges both AA and AAA batteries and includes 4× AA Eneloop batteries straight out of the box. Eneloop ...

SKU: DF-FIT1002 | Brand: DFRobot

The photonic thin-film battery is an advanced energy-harvesting solution that stands out from traditional solar cells and amorphous silicon photonic cells due to its higher conversion efficiency and output power. Made...

SKU: EF-EF08182 | Brand: ElecFreaks

This kit contains a micro:bit board, a USB cable and a battery holder. This is a basic kit for using micro:bit. Micro:bit board is launched by BBC which aims to help children at or above 7 grade to learn programming b...

SKU: DF-FIT0619 | Brand: DFRobot

This battery holder connects 3× AA batteries in series, providing approximately 4.5V from alkaline cells. It features a PH2.0-2P connector with a 15cm wire lead, making it compatible with DFRobot boards and other devi...

SKU: SF-PRT-15217 | Brand: SparkFun

The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and prov...

SKU: AF-3788 | Brand: Adafruit

A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and ...

SKU: AF-1867 | Brand: Adafruit

A breakout board with a CR1220 coin cell battery holder, an on/off switch, and 0.1″ pitch breakout pins. Ideal for powering very low-current projects or providing switchable battery backup for a real-time clock (RTC) ...